Rich :
Mine was used with a Heil for awhile and had to crank it back down for my
homemade electret boom mic.
John N1JM
-----Original Message-----
From: tentec-admin@contesting.com [mailto:tentec-admin@contesting.com]On
Behalf Of Rich McCabe
Sent: Thursday, June 27, 2002 10:28 PM
To: TenTec@contesting.com
Subject: Re: [TenTec] Pegasus mike gain
Thank you John.
That did the trick... I thought I was getting lots of drive and this would
not fix the VOX but it works great now.
I might have to put a dab of finger nail polish on it though. It is sitting
at almost off and has a hair trigger. I am afraid it will move.
Now all I need to do is find some "real" screws and I will have a decent rig
!
73,
Rich
kd0zv
----- Original Message -----
From: "John L Merrill" <jmerrill1@adelphia.net>
To: "Rich McCabe" <rich@1967z28.com>
Sent: Thursday, June 27, 2002 9:13 PM
Subject: RE: [TenTec] Pegasus mike gain
> The mic gain pot is the one you mentioned. You can adjust that to make up
> for low output mics such as the Heils. There is mention of it in the
manual
> but it doesnt tell you where it is.
>
> John N1JM
>
> -----Original Message-----
> From: tentec-admin@contesting.com [mailto:tentec-admin@contesting.com]On
> Behalf Of Rich McCabe
> Sent: Thursday, June 27, 2002 9:29 PM
> To: TenTec@contesting.com
> Subject: [TenTec] Pegasus mike gain
>
>
> First, I want to say thanks to those who responded a couple weeks ago to
my
> "sick Pegasus" post.
>
> It did turn out to be leaky finals as most people replied. Unfortunately
Ten
> Tec would not send a PA unit out and it had to back for service. The rig
is
> less than a month old and I never have been able to get the vox to work so
I
> ask them to check it. It returned with the slip saying VOX checked OK.
>
> Well I still cant get it to work !
>
> I am running a Heil Classic mike and I have heard complaints that the Heil
> does not drive the Pegasus well.
>
> I had talked to Service before it went back and they suggested turning up
> the internal gain. Where is it? I looked and did not see anything
obvious.
> There is a tiny unlabeled trim pot near the header that the mike connects
to
> on the board but I do not see anything else.
>
> Couple other gripes !
>
> 1) It would be nice if Ten Tec would use decent screws on the case and not
> the kind you hold McDonalds happy meal toys together with. I am going to
> replace them so I am able to get them out next time.
>
> 2) It would also be appreciated if the would return the rig the way it
left.
> I added a small piece of coax internally to the aux jack so I could run
the
> RX-320 as a second receiver. It didn't work when it came back and after
> fighting the above mentioned case screws I find the wire is gone. Geez
guys
> if you are going to remove it, at least leave me a note saying you did.
Oh,
> I forgot it is against Ten Tec policy for the tech to write anything
> substantial on the return ticket.
>
> That said, they still are my favorite radio company :)
>
> Any help on the mike gain location?
>
> Thanks,
>
> Rich
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> ---
> Incoming mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
To: <tentec@contesting.com>
> Version: 6.0.372 / Virus Database: 207 - Release Date: 6/20/2002
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
---
Incoming mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
To: <tentec@contesting.com>
Version: 6.0.372 / Virus Database: 207 - Release Date: 6/20/2002
|