I think my previous message went but not sure... I think on your board
layout like mine here, D18 is the first diode not the second as you
state.... I think the first one is D19 which shows up on the service manual
schematic and board layout but is not there on the newer models of the amp.
Jim K4JAF
----- Original Message -----
From: Michael M. Raskin <mraskin@mediaone.net>
To: Jim Cox <jcox@digitalexp.com>
Sent: Saturday, November 10, 2001 8:10 AM
Subject: Re: PW-1
> Thanks for the reply, Jim. My s.n is 1307 and the Main Unit board is
> the"B" board, which shows D18 as the 2nd one down, just to the left of
> the vertically mounted resistor. I'll take a look at the board again
> (or have a younger ham with better eyes) to make sure nothing is left.
> It essentially disintegrated when I grabbed it.
> 73,
> Mike, W4UM (ex-K4KUZ) mraskin@mediaone.net or w4um@arrl.net
> Florida Contest Group http://www.qsl.net/fcg/
> South Florida DX Association http://www.qsl.net/k4fk/
> ----- Original Message -----
> From: "Jim Cox" <jcox@digitalexp.com>
> To: "Michael M. Raskin" <mraskin@mediaone.net>
> Sent: Saturday, November 10, 2001 8:56 AM
> Subject: Re: PW-1
>
>
> > It should work on 10/12 after the diode is removed. Mine did, make
> sure you
> > reset the amplifier. You said you crushed the diode, I assume there
> is
> > nothing on the traces left. I noticed on my board that one of the
> diodes
> > above d18 was missing, so diode 18 was the second one down, not the
> third as
> > shown on my circuit board trace layout from the service manual.
> Dont know
> > what the problem could be. You have to very finely adjust the
> alc pot,
> > it is very coarse tuning.
> > Jim K4JAF
> >
> >
> > ----- Original Message -----
> > From: Michael M. Raskin <mraskin@mediaone.net>
> > To: <jcox@digitalexp.com>
> > Sent: Friday, November 09, 2001 10:56 PM
> > Subject: PW-1
> >
> >
> > > Hi Jim - Saw your recent posting about the PW-1. I just got one
> and
> > > am trying to set it up with my 756-PRO. The only problem I am
> having
> > > is that I can't get it to work on 10 or 12. I enlarged the view
> of
> > > the main unit board and I am certain I remove D18 -- "remove" is
> > > probably a poor choice of words since the mini needle-nosed pliers
> > > "destroyed" the surface-mounted unit with not much pressure.
> Anyhow,
> > > I'm sure it's the correct one. I then reset the CPU. Is there
> > > something I'm missing? BTW, the ALC adjustment is hair-trigger,
> as
> > > best, and quite flimsy - I found that a little too much pressure
> bent
> > > it back 90 degrees and thank God for ultra thin bent-tip tweezers.
> > >
> > > 73,
> > > Mike, W4UM (ex-K4KUZ) mraskin@mediaone.net or w4um@arrl.net
> > > Florida Contest Group http://www.qsl.net/fcg/
> > > South Florida DX Association http://www.qsl.net/k4fk/
> > >
> > >
> > >
> >
> >
>
>
>
|