Arthur,
There's not too much that has to be done to power
an electret element. You really don't absolutely need
to get the 705 element. YOu could use a two wire
element from Radio Shack and probably get very good
results. I have a Plantronics headset that I modified
to work with my Pegasus. It had a two wire mike as
well. Here's how mine's done.
1k 1/4 watt
Electret |-------/\/\/\----------> to Pin 4 (+4)
Element |
----- + | + 6.8 mf Tantalum
| |--------|-------| |-------------> to Pin 1 (Mike)
| |
| |--------------------------------> to Pin 2 (GND)
----- - (Shielded Cable)
The Resistor and Capacitor are in the mike plug.
That's why I used a tantalum cap and 1/4 watt res. You
could use a 1/8 watt too. I just used what I had on
hand.
Note the polarity on the electret element and the
Cap.
--- Arthur R Bernstein <n2ka@juno.com> wrote:
>
> --------- Begin forwarded message ----------
> From: Arthur R Bernstein <n2ka@juno.com>
> To: TenTec@contesting.com
> Subject: [TenTec] TT 705 Cartridge in headset-boom
> mike??
To: <tentec@contesting.com>
> Date: Tue, 12 Oct 1999 01:33:27 EDT
> __Message-ID: <19991012.012351.4463.0.N2KA@juno.com>
> READ FOLLOWING (PREVIOUSLY POSTED MESSAGE). ANYONE
> HAVE ANY SUGGESTIONS
> FOR A REPLACEMENT ELEMENT FOR THIS HEADSET???????
>
__________________________________________________________________
> Hi Group, I've just recently acquired a nice headset
> with a boom mike.
> It's an Azden HS-03. Unfortunately, I don't think
> these are readily
> available in the U.S. anymore, since Azden has
> stopped distribution of
> all their gear in this country. The microphone is
> attached to a thin,
> curved stainless steel tube through which a thin
> shielded mike cable
> runs. It appears to be single conductor shielded.
> I've noticed that the
> output from the mike element is not sufficient to
> drive my OMNI VI very
> well, even with the mike gain cranked way, way up
> (I'm familiar w/cranked
> up mike gain as I use the Heil HM-10 dual element
> mike.) The cartridge
> is approximately the diameter across of a
> quarter-it's a dynamic with a
> stated impedance of 500 ohms. No specifics given to
> voltage output.
> Frequency response is given as 300-4000hz w/ a 6db
> rise at 2500 hz,
> actually -10db at 300 hz (that's fine.) Was thinking
> of buying a 705
> element from Ten Tec and substituting it into the
> boom mike holder. The
> only problem I see is I believe the 705 is an
> electret and needs +4vdc on
> it, supplied by pin 4 on the OMNI VI. I dont think
> I could squeeze
> another wire into the mike boom tube tto get the +4v
> on the element. Is
> there another way to do this such as piggybacking
> the 4v on the audio
> line? How would this be done? Or would I have to run
> an external wire
> heat shrink tubed to the boom for the voltage.? This
> setup could be used
> with footswitch if I wire in a
> jack to mike connector between pin 3 and ground.-as
> Heil does.
> Any suggestions or ideas?
> Thanks in advance.
> 73,
> Art, N2KA.. (95% CW!!!)
>
___________________________________________________________________
> Get
> the Internet just the way you want it. Free
> software, free e-mail, and
> free Internet access for a month! Try Juno Web:
> http://dl.www.juno.com/dynoget/tagj. -- FAQ on WWW:
>
> http://www.contesting.com/tentecfaq.htm Submissions:
>
> tentec@contesting.com Administrative requests:
> tentec-REQUEST@contesting.com Problems:
>
> owner-tentec@contesting.com Search:
>
> http://www.contesting.com/km9p/search.htm
> --------- End forwarded message ----------
>
>
________________________________________________________________
> YOU'RE PAYING TOO MUCH FOR THE INTERNET!
> Juno now offers FREE Internet Access!
> Try it today - there's no risk! For your FREE
> software, visit:
> http://dl.www.juno.com/get/tagj.
>
> --
> FAQ on WWW:
> http://www.contesting.com/tentecfaq.htm
> Submissions: tentec@contesting.com
> Administrative requests:
> tentec-REQUEST@contesting.com
> Problems:
> owner-tentec@contesting.com
> Search:
> http://www.contesting.com/km9p/search.htm
>
>
_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address at http://mail.yahoo.com
--
FAQ on WWW: http://www.contesting.com/tentecfaq.htm
Submissions: tentec@contesting.com
Administrative requests: tentec-REQUEST@contesting.com
Problems: owner-tentec@contesting.com
Search: http://www.contesting.com/km9p/search.htm
|