Hi Paul,
I did notice in SDC over the weekend that PageUp/PageDN didn't work to
change CW speed unless I turned off winkey. Then it worked for the internal
keyer. As soon as I tunred winkey back on to use my keyer, it went back to
whatever it was set at. I could adjust the speed with the keyer knob but
only if there was nothing in the callsign field. It really made it difficult
trying to match sending speeds with other stations.
I'll try 13.40 and see if it's fixed.
Thanks -- Paul
> -----Original Message-----
> From: sd-user-bounces@contesting.com
> [mailto:sd-user-bounces@contesting.com] On Behalf Of Paul O'Kane
> Sent: March 10, 2008 18:23
> To: sd-user@contesting.com
> Subject: [SD-User] SD and WinKey
>
> I've revised SD's code for WinKey, and I'd appreciate any
> feedback on how the changes are working before releasing V13.40.
>
> This version of SD is numbered V13.39A and is available
> (SD.EXE only) from www.ei5di.com/sd/sdexe.zip.
>
> Let me know what you find.
>
> 73,
> Paul EI5DI
>
> _______________________________________________
>
>
> WinKey Speed Changes:
> With WinKey enabled, the WKSPEED command lets you
> choose between speed changes from the keyboard (K)
> or WinKey's speed pot (P) - the default. SPEED
> and POT are alternatives to WKSPEED. You can check
> your settings with the STATUS command.
>
> Temporary speed changes within messages are now
> reliable and consistent. Use #1 to #9 to increase
> speed - from the current WPM value. They may be
> chained - for example #9#9 gives a temporary 18
> WPM increase. To reduce speed, use #-1 to #-9.
>
> To reset speed to the default value, use #0. SD
> adds this to the end of all messages - you don't
> need to do this yourself, and it's no harm if you
> do.
>
> Restrictions:
> When speed is controlled by WinKey's pot -
> 1. Instant QRS, using semi-colon, is disabled.
> 2. When playing a message with temporary speed
> changes or with the #C callsign parameter, and
> you change speed with the pot, the WPM display
> is not updated until the message ends.
>
> When speed is controlled by the keyboard -
> 1. The maximum speed possible is the sum of
> WinKey's MINWPM and WPMRANGE settings. STATUS
> shows the relevant values.
>
> With internal keying (WINKEY disabled), the speed
> change and "instant QRS" features work only when no
> message is playing.
>
> If this sounds a bit complicated, you're right.
> It's not so simple to control WinKey while
> supporting all possible speed options.
>
> ESM:
> With ESM enabled in RUN mode, and the exchange
> started before completing the callsign, any
> additional callsign edits (by returning to the
> callsign field before logging) were picked up by
> the keyer but were not logged. Fixed. Thanks
> G4RCG.
>
> Keyer:
> When you log a QSO, and then edit the callsign
> already logged, the #C (callsign) keyer parameter
> now plays the edited callsign - when the callsign
> field on the logging line is empty. Thanks YU2DRA.
>
> _______________________________________________
> SD-User mailing list
> SD-User@contesting.com
> http://lists.contesting.com/mailman/listinfo/sd-user
>
_______________________________________________
SD-User mailing list
SD-User@contesting.com
http://lists.contesting.com/mailman/listinfo/sd-user
|