RTTY
[Top] [All Lists]

Re: [RTTY] [MMTTY] Spot frequency

To: <MMTTY@yahoogroups.com>, "RTTY Contesting" <rtty@contesting.com>
Subject: Re: [RTTY] [MMTTY] Spot frequency
From: "Robert Chudek - K0RC" <k0rc@citlink.net>
Reply-to: Robert Chudek - K0RC <k0rc@citlink.net>
Date: Sun, 13 Jun 2010 20:47:34 -0500
List-post: <rtty@contesting.com">mailto:rtty@contesting.com>
Gary,

There were a couple of excellent descriptions of what is "going on" with RTTY 
spots not appearing on the real Mark frequency by some operators.

Specific to the MP-1000MP, the fourth paragraph on page 54 of the Yaesu manual 
(that I downloaded off their website) shows the options for this radio. It says 
the default setting will display the Mark signal frequency, which is what you 
want when you post a spot. Unless you have changed this, you should be "set to 
go".

In addition to checking this menu setting, you can determine whether your radio 
is displaying the Mark frequency by tuning in WWV at 10-MHz. When your radio is 
set correctly in RTTY mode, you will hear the Mark audio signal (2125 Hz) 
generated by the WWV carrier. If the signal is zero beat, the radio is 
displaying the suppressed carrier frequency.

I know N1MM Logger has the ability to "correct" the spot frequency if a 
transceiver does not generate the proper Mark RF frequency. I believe WriteLog 
does too, but someone using that software should verify my statement about this.

73 de Bob - KØRC in MN



  ----- Original Message ----- 
  From: Gary AL9A 
  To: RTTY Contesting ; MMTTY 
  Sent: Sunday, June 13, 2010 7:18 PM
  Subject: [MMTTY] Spot frequency


    
  I've read stuff about this before, but would appreciate it if someone could 
  refresh my memory. During the DLDC contest I was spotted several times by 
  various stations. Most spots were at or very near my VFO frequency. 
  However, I noticed a few spots that were a couple of kHz below or above my 
  VFO frequency. For example, while running at 14082.75 (FSK) I was spotted 
  at 14080.6. Another time I was spotted 2.1 kHz above my VFO frequency.

  I seem to remember this was due to the 2125 Hz shift. Is this a difference 
  between running FSK or AFSK? In the example above was that due to the 
  spotting station running AFSK on LSB? What about the spots above my 
  frequency? AFSK on USB? And what about the spots I send out while using 
  FSK. Are my spot frequencies correct or off too? It was a bit annoying to 
  call CQ endlessly and finally see someone spot me, but on the wrong 
  frequency! Can someone clarify this for me?

  73,
  Gary AL9A



  __._,_.___
  Reply to sender | Reply to group | Reply via web post | Start a New Topic 
  Messages in this topic (1) 
  Recent Activity: a.. New Members 5 
  Visit Your Group 
  MARKETPLACE
  Stay on top of your group activity without leaving the page you're on - Get 
the Yahoo! Toolbar now.

   

------------------------------------------------------------------------------

  Get great advice about dogs and cats. Visit the Dog & Cat Answers Center.

   

------------------------------------------------------------------------------

  Get real-time World Cup coverage on the Yahoo! Toolbar. Download now to win a 
signed team jersey!

    Switch to: Text-Only, Daily Digest . Unsubscribe . Terms of Use.
   
  __,_._,___
_______________________________________________
RTTY mailing list
RTTY@contesting.com
http://lists.contesting.com/mailman/listinfo/rtty

<Prev in Thread] Current Thread [Next in Thread>