Bob --
I had a similar problem recently after adding a few more devices to my PC
(camera, extra parallel port, new modem that worked in DOS mode too, etc).
Turned out I had run out of IRQs and my comm port to the FT-1000MP was
having an IRQ conflict. Rather than work around it by setting a few devices
to be disabled and not using IRQs in DOS mode I took the quick and easy way
out and pulled the extra parallel port card and that freed up an IRQ (once I
"removed" the comm port then reinstalled it and let Windows assign it the
new unused IRQ). Go to Start/Control Panel/System/Device Manager and click
on "computer" at the top and check out your IRQs. Also, the comtsr setting
I use is -b4800 -n82.
In some defense of Ken he is a really talented software guy but he has
little occasion to spend much time with the myriad of problems with radio/PC
interfacing so these type of questions are probably better answered by
posting them to the reflector (which is what you're doing). If my answer
isn't the right one, I hope someone comes up with a fix for you.
Good luck!
Gary, W0TM
http://www.w0tm.com
-----Original Message-----
From: owner-ct-user@contesting.com
[mailto:owner-ct-user@contesting.com]On Behalf Of Robert L. Shohet
Sent: Saturday, September 18, 1999 4:19 PM
To: 1000mp@qth.net
Subject: [ct-user] Problems with FT1000MP and CT
Gentlemen:
I have discovered a VERY vexing problem that I would appreciate your
thought and insight on as well as any ideas to cure the problem.
In the past few contests I have attempted to use CT and my FT1000MP. It
has been a TOTAL DISASTER!!!
In the past, Version 9.32 seemed to work ok, as did 9.36 but then the
problems started.
In IARU & WAE here's what happened:
The radio is on 21000 but CT shows "20". I type 21000 and hit enter and
then CT shows "15" but when I log a qso, CT changes the band to "20",
logs the qso on 20 and then shows that I am still operating on 20. CT
also says "Radio Timeout". Meanwhile the frequency of the radio still
shows 21000!
To get around this and having to GO BACK and retroactively change the
band on every qso,
qso, I then typed "." which switched me to Radio 2 which then would log
the band of the qso correctly but still would not follow the radio
frequency when the radio changed bands and would not correctly record
the frequency. I also was not able to communicate with a second
computer on my 2nd radio anymore.
Thinking that the latest version of CT might be causing "indigestion" I
tried versions 9.32, 9.36 & 9.40. NO LUCK! Still same problem.
OK, now I set about eliminating the obvious. I tried (with no success)
the following:
1) Changed the data cable between radio and FT1000MP (Still had problem)
2) Changed COM port on computer (Still had problem)
3) Loaded and Unloaded COMTSR's (Still had problem)
4) Tried complete RESET of FT1000MP (Still had problem)
5) Tried previously working versions of CT (Still had problem)
6) Reconfirmed previous working settings for the COMTSR's as -b4800,
-e71
(still had problem)
I have tried everything that I can think of with absolutely no success.
Apparently CT partially communicates with the radio and the radio only
partially communicates with CT.
The bottom line is now CT ALWAYS says "RADIO TIMEOUT" and wants to log
every qso on 20 meters. It will not record the correct freq. of the
qso, will not let the two radio computers talk with each other and the
radio and the computer do not communicate effectively with each other.
K1EA has summarily IGNORED and NOT responded to my communications
regarding this problem.
Does anyone know what might be causing this problem and how to fix it?
I would appreciate all thoughts and ideas on this problem.
Tnx for your help!
73
Bob KQ2M
--
Submissions: ct-user@contesting.com
Administrative requests: ct-user-REQUEST@contesting.com
WWW: http://www.k1ea.com/
Questions: owner-ct-user@contesting.com
--
Submissions: ct-user@contesting.com
Administrative requests: ct-user-REQUEST@contesting.com
WWW: http://www.k1ea.com/
Questions: owner-ct-user@contesting.com
|