Date: Fri, 15 Mar 2019 10:37:37 -0500
From: donroden@hiwaay.net
To: amps@contesting.com
Subject: [Amps] Question about grid current in 4CX or 3CX
<Question
<For the larger tubes with handles ( commercial service )
<Does grid current increase or decrease as plate voltage and screen
<voltage is removed. ?
<If it takes 250 watts to produce 100ma of grid current in a 4CX10,000.
<is the grid just a big dummy load and is it doing the tube harm to
<dump 250 watts into it when both plate and screen voltages are removed ?
<Don W4DNR
## I am assuming in the case of the 3CX series, that the grid is bonded to
chassis
via the GG socket..and tube is cathode driven.... just like any GG triode.
## I am assuming the 4CX tetrode is being grid driven, with the usual
screen and B+
voltages applied.
## In the case of the GG triode, and no B+... but drive still applied, you
will send the grid
current through the roof ! Without any B+, the tube now thinks the control
grid is the anode.
All the electrons will flow from directly heated cathode to the control
grid. I have verified this
several times on several different triodes, including the larger metal types.
Thats why I install
a rear panel 3AGC fuse holder, and wire it between chassis....and the
negative terminal of the
dc grid meter. Then use a FAST fuse, thats barely rated for normal average
dc grid current.
## If you lose the B+, and dc grid current skyrockets, grid fuse blows open
asap. With NO path
for dc grid current, triode can not be driven. Power output drops to ZERO.
Input swr, between
xcvr and input to the GG triode amp rises to infinity. Xcvr then shuts
itself down asap. Event over.
## On GG triodes, with delicate 4 watt grids, like the 3CX-800A7, and loss
of B+, whats then required
is high speed electronic grid over current protection. Another method is if
B+ falls below a certain threshold,say
less than 70% of normal, amp kicks off line asap. For GG triodes like
3-500Z, 3x3, 3x6, 3x10, 3x15 etc, the
grid fuse is ample.
## IF the tetrode is run like a high mu triode, with both screen grid and
control grid bonded to chassis,
use the grid fuse method. This config requires a lot of drive...like 625
watts. Back in the day, a SB-220,
run in the CW position was used for the ipa.
## IF the tetrode is grid driven, with the usual screen and B+ applied, and
the typ 450 ohm globar used to
derive grid voltage..when driven through the typ 1: 9 un-un......and screen
and B+ are simultaneously
removed... I THINK the globar just dissipates the normal drive power. But
dunno if the dc grid current increases
or not. On the grid driven tetrode, run in passive grid with the 1:9 un-un
and 450 ohm globar, the dc grid current
is typ 0 ma... if tube run in class AB1. Typ the 4CX-10,000A7, when grid
driven In the passive grid config,
only requires 130 watts for 14 kw pep output. You would never require 250
watts.
## On tetrodes like the 4CX-1000 variety, complete with their ZERO watt
grid diss rating, grid over current is
required, and will kick amp offline with just 100 microamps of grid
current.
## Then u can also get into goofy configs with the same tetrode, like just
loss of screen voltage.... or just loss
of B+. On the commercial tetrode amps, like collins 208-U series and
similar from others like aerocom, etc
they all had plate over current, screen overcurrent,and grid over current
relays and protection built in..and all 3
have adjustable thresholds.
Later... Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|