Re: [Amps] SB220 step start blows fuses

[donroden@hiwaay.net]

I think you are seeing a normal condition . Measure the voltage at the  
input of the Amp.    Use a light wattage that gives at least 1/2  
voltage at the amp.
Your filament transformer appears to be fine.  Turn on the HV with the  
tubes out and test again.
Don W4DNR


Quoting Warren Volz <warren@warrenvolz.com>:

> I may shortly be looking to purchase a variac.
>
> After building a dim bulb tester this weekend I have a minor update.
>
> With 120V connected, the HV primary disconnected and one tube in a  
> socket (doesn’t matter which I use) the 100W bulb in my tester  
> lights up bright. No fan and the meter lights aren’t on. If I take  
> out the tube the fan and meter lights work. So I guess I have a  
> shorted tube? Would it be good to double check the DC/AC voltage on  
> the filament supply with the tubes plugged in? That would show any  
> sags that might exist.
> -Warren
>
> > On Jul 7, 2017, at 12:58 PM, gudguyham--- via Amps  
> > <amps@contesting.com> wrote:
> > I know I sound like a broken record but yes, a Variac is the way to  
> > go.  Especially with amps that can have power supply problems and  
> > gassy tubes.  You will hear the plate transformer groan and won't  
> > see HV climbing on the meter if there is a problem in the PS long  
> > before the smoke Genie appears.  My Variac gets used daily several  
> > times after doing ANY work on an amp.  It's saved me loads of time  
> > fixing blown parts that would normally occur if I had just turned  
> > an amp on with problems.  Best investment I ever made.  0-250 volts  
> > at 20 amps.
> > Sent from AOL Mobile Mail
> >
> >
> > -----Original Message-----
> > From: Bill Turner <dezrat@outlook.com>
> > To: Amps group <amps@contesting.com>
> > Sent: Fri, Jul 7, 2017 12:34 PM
> > Subject: Re: [Amps] SB220 step start blows fuses
> >
> >
> > ------------ ORIGINAL MESSAGE ------------(may be snipped)
> >
> > On Fri, 7 Jul 2017 10:21:36 -0400, Mark B. wrote:
> >
> > > A variac varies voltage.   It is not designed to limit current.
> > REPLY:
> >
> > At the very low end of its range, a Variac limits current just fine. I
> > worked as a calibration technician at Tektronix for years, taking
> > brand new scopes off the assembly line and powering them up for the
> > first time. Believe me, a Variac is the only way to go with a unit
> > which could have any number of problems at first. Over the years I
> > powered up literally thousands of scopes this way and never a problem
> > with current limiting.
> >
> > 73, Bill W6WRT
> > _______________________________________________
> > Amps mailing list
> > <a href="mailto:Amps@contesting.com";>Amps@contesting.com</a>
> > <a href="http://lists.contesting.com/mailman/listinfo/amps";  
> > target="_blank">http://lists.contesting.com/mailman/listinfo/amps</a>
> > _______________________________________________
> > Amps mailing list
> > Amps@contesting.com
> > http://lists.contesting.com/mailman/listinfo/amps
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps


DonR
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps