Date: Wed, 1 Apr 2015 16:37:16 +0100
From: Chris Wilson <chris@chriswilson.tv>
To: Bill Turner <dezrat@outlook.com>, amps@contesting.com
Subject: Re: [Amps] more - oil bath GS-35b
Message-ID: <905754433.20150401163716@chriswilson.tv>
Content-Type: text/plain; charset=us-ascii
There are optimum flow rates based on heat exchanger coolant medium,
be it gaseous, or fluid, the type of liquid, and its viscosity. It
also depends on the surface area of the inside and outside elements of
the exchanger and the device being cooled. For sure faster flow is
*NOT* necessarily better. In automotive racing water (or water mix)
coolant is NOT flowed as fast as possible through the engine, but very
careful design has water flow going at different rates in different
parts of the engine. Those who have replaced a cylinder head gasket
may have noticed the flow restriction hoses of varying sizes in the
head and gasket. Different areas of the engine run at different
temperatures, and flow rate is varied to optimize heat extraction.
Water to air radiators have internal turbulators in high end coolers
to increase internal surface areas, thermostats have restrictor plates
to control water flow rates. Current cooling systems use electronic
water pump drives and electronic thermostats to optimize flow
according to load, blah blah.
Air flow through heat exchangers is similarly regulated for optimum
heat exchange speeds.
I am sure in an oil to air heat exchanger with a submerged valve there
will be an optimal flow rate for the oil and the air, that is far away
from the fastest flow rate, and there are big differences between
convection, conduction and radiation. I am most definitely *NOT* a
heat transfer engineer, but I am a race car engineer and I know a lot
of science and experimentation goes on in the engine world to maximize
heat exchanger performance, and engine coolant flow is a lot slower
than you perhaps imagine.
--
Best regards,
Chris mailto:chris@chriswilson.tv
### Us hot rodders run into this exact same issue with superchargers on V8
engines.
The intercooler is just a small radiator, typ bar + fin type... placed on the
hot output
of the supercharger. Its job is to EXTRACT heat. A small pump passes the
distilled
water /glycol mix to the HE, aka heat exchanger..aka rad # 2. The HEs job is
to DUMP heat.
Mine doesn’t have a fan on the HE,but simply relies on airflow due to vehicle
speed.
Some will use dual fans on the HE, to keep things cooled down a bit at red
lights,
and also between runs at the drag strip etc. For road course folks, the fans
don’t provide
any benefit once above 20-30 mph. They impede airflow.
## faster pump speeds will make the intercooler work better..and extract more
heat,
BUT the entire assy is one big loop. Pump the hot water/glycol coolant through
the
intercooler-HE loop too fast, and all you end up doing is spinning hot water
around,
with no increase in eff at all. Unless the HE (external radiator in the case
of the GS35B)
can dump the heat as fast as its being generated, you are wasting your time
with faster pump speeds.
## 1 watt = 3.15 BTU. 1 kw = 3150 BTU In the case of the proposed GS35B
setup, 1-2 kw CCS of heat to extract..then dump is not a big issue. And with
ssb /cw modes, the heat generated is going to be a lot less. Beware of
advertised GPM
flow rates on pumps. They are typ for no load. IE: fire hose connected from
55 gallon
drum of water, to input of pump.... then another big diam hose from output to
the ground.
## Once actually hooked up to the tight bends and puny size fittings, small
tubing, and
the restrictions inside the GS35B tube and the external radiator, the actual
measured flow rates
drop like a rock. Install a much bigger pump, and flow rates typ increase
very little
if any.
## check out the BTU specs for small radiators...like automatic transmission
coolers.
They are typ 8000-20,000 BTU rated..provided airflow of XXX CFM is put through
em.
I had to install a 2nd auto tranny cooler in series with my oem cooler, since
the tranny temps
climbed way too fast in just a few secs when super charger on..and gas pedal
mashed. Like
170-200 F in just 7 secs.
## Old style radiators were tube + fin type. Better types are bar + plate.
You can also get em
in single, dual or triple core..and also single and dual pass. My bar + plate
Tranny cooler uses a unique
T stat......operates on viscosity. The hotter the synthetic tranny fluid
gets, the higher it rides up either side
of the rad. At that point it makes more and more parallel passes from one
side to the other.
## The GS35B, with its low dissipation, will not be an issue. Perhaps
2-5000 btu at most.
Ultimately... ALL the heat has to be eventually transferred to the air ! BTW,
you will have to provide
some cooling to the base seals of the tube, where the fil connections are made.
With Eimac water cooled
tubes, or vapor phase cooled tubes, a small air pump, is used to cool the fil
pins.
Same deal with a normal air cooled tube which uses anode to base flow....
instead of the usual base to anode flow,
typ 3-5 cfm on a 3CX-3000A7. But uses anode to base flow ...nobody..its fubar
and requires way more cfm.
The additional air flow to the base will not be required if the entire tube is
immersed in oil, like you proposed.
## A 2-4 GPM pump will more than meet your requirements. Then perhaps a
pair of 120 mm square
fans, like the 65 cfm rotron whisper types.. placed in front of the external
rad. They are very quiet, and can be
further lowered in speed with a simple metal finned resistor, variac, variable
dc supply etc. Shroud the front of the
rad, where the fans are... other wise you are wasting your time... air will
leak like a sieve out the sides.
Un shrouded rads don’t work too well. IMO, you are better off pushing air
through the rad, vs sucking
it through the back end of the rad. Then you don’t have hot air passing in and
out past the fan bearings.
later.... Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|