Amps
[Top] [All Lists]

Re: [Amps] Holding a vacuum

To: Carl <km1h@jeremy.qozzy.com>
Subject: Re: [Amps] Holding a vacuum
From: Kim Elmore <cw_de_n5op@sbcglobal.net>
Date: Mon, 1 Dec 2014 14:38:47 -0600
List-post: <amps@contesting.com">mailto:amps@contesting.com>
Ah! Thanks, Carl. This does, however, raise another question: when read here 
about storage life of transmitting tubes and whether they become gassy, it 
seems from what you write that whatever happens isn't due to air entering the 
tube, but rather from the internals of the tube out gassing. Is that correct?

Kim N5OP

"People that make music together cannot be enemies, at least as long as the 
music lasts." -- Paul Hindemith

> On Dec 1, 2014, at 14:24, "Carl" <km1h@jeremy.qozzy.com> wrote:
> 
> It all depends upon what you mean by gas and what is its density.
> 
> Altho the air we breathe is a gas it is not called that in tube technology 
> and to avoid the misinterpertation it is referred to as "going to air" such 
> as with a seal leak or actual breakage.
> 
> A serious air leak will destroy the filament while a minor one will show the 
> telltale color right at the filament or cathode. If the HV applied to a minor 
> leak is well below the witholding ability of the tube and the filaments 
> critical point, that glow is all there is. A 3-500Z with 2500V applied to a 
> tube that will hi pot to 12KV or more wont break down as long as the real 
> "gas" isnt also present to any great amount.
> If there is an additional gas glow between grid and anode then an arc could 
> easily occur.
> 
> I wouldnt trust any tube that doesnt hi pot to at least 3X the operating 
> voltage and AM already peaks at 2X plus the modulation index above 1 so 4X is 
> the mnimum safe point
> 
> A gas presence can arc at as low as 1500V or so or not even at 2500V yet in a 
> 3-500. There will not be any difference in plate current until the actual 
> plasma arc occurs which will often continue until the HV is completely shut 
> and bled off. Often applying RF will trigger it which is why those who try 
> running a tube out of resonance as an "easy" way to increase anode color at a 
> lower voltage, say 1800V as in many amps with a CW/SSB switch, get a nasty 
> surprise. An outgassed tube can often be regettered by running  HV in the 
> 1000-1200V range and rebiased to draw sufficient plate current to get a nice 
> bright to brick red anode glow. There is no guarantee a particular tube will 
> regetter sufficiently to run at 2500V or more but Ive had about a 60-70% 
> success rate over several decades. Some that wont hold up at say 3500V will 
> last for many years in a SB-220 for instance.
> 
> Gas as referred to here is the result of the manufacturing process which is 
> recombined into the anode by a gettering process as one of the last 
> manufacturing steps. Over time and also with prolonged excessive dissipation 
> the gas will be re-released.
> 
> Ceramic metal tubes react similarly but not visibly and the gettering is 
> slightly different. Regettering often requires just running the filament from 
> hours to days.
> 
> One way to avoid all this gettering issue is to beat on the tube regularly to 
> keep it gettered. The original 1986 Eimac 3-500Z's in my LK-500ZC were 
> regularly run in serious contesting and more recently as an AM linear.....if 
> I have to run up the electric bill I might as well enjoy doing it!
> 
> Carl
> KM1H
> 
> 
> 
> ----- Original Message ----- From: "Kimberly Elmore" 
> <cw_de_n5op@sbcglobal.net>
> To: "Amps group" <amps@contesting.com>
> Sent: Monday, December 01, 2014 1:34 PM
> Subject: Re: [Amps] Holding a vacuum
> 
> 
>> I always thought that a gassy tube is essentially a short when HV is 
>> applied, or perhaps like a thyratron: once current is allowed to flow by the 
>> control grid it can't be stopped until the cathode line is opened. 
>> Gas-filled rectifiers, such as the 3B28, 866A, etc., or the gas-filled VR 
>> tubes are examples. Is there an "in between" state where a tube is gassy and 
>> works fine except for excess plate current?
>> 
>> Kim N5OP
>> 
>> 
>> ________________________________
>> From: Bill Turner <dezrat@outlook.com>
>> To: Amps group <amps@contesting.com>
>> Sent: Monday, December 1, 2014 11:38 AM
>> Subject: Re: [Amps] Holding a vacuum
>> 
>> 
>> ------------ ORIGINAL MESSAGE ------------(may be snipped)
>> 
>>> On Thu, 27 Nov 2014 19:15:08 -0500, you wrote:
>>> 
>>> What metric does one use to determine if a given tube holds a vacuum or 
>>> not?>
>>> Cheers,
>>> 
>>> Karin   K3UU
>> 
>> REPLY:
>> 
>> Tubes that lose vacuum draw excess anode current even when idling and
>> if they are glass, one can see a blue glow in between the elements
>> when HV is applied.
>> 
>> 73, Bill W6WRT
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>> 
>> 
>> -----
>> No virus found in this message.
>> Checked by AVG - www.avg.com
>> Version: 2015.0.5577 / Virus Database: 4223/8663 - Release Date: 12/01/14
> 
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>