That's it, Carl.
73/jeff/ac0c
www.ac0c.com
alpha-charlie-zero-charlie
-----Original Message-----
From: Carl
Sent: Saturday, March 24, 2012 7:34 PM
To: Jeff Blaine ; jim@audiosystemsgroup.com ; amps@contesting.com
Subject: Re: [Amps] Guidelines.....toroids for tank ckts
Scotch 27 Jeff.
Carl
KM1H
----- Original Message -----
From: "Jeff Blaine" <keepwalking188@yahoo.com>
To: <jim@audiosystemsgroup.com>; <amps@contesting.com>
Sent: Saturday, March 24, 2012 7:16 PM
Subject: Re: [Amps] Guidelines.....toroids for tank ckts
> Dave,
>
> For the low bands, the #2 red is pretty widely used. The 3M tape for that
> (forget the number) is pretty expensive but it's strong and won't
> breakdown
> in moderate heating. For the higher bands, air core types are small
> enough
> to fit even into some tiny spaces so there's typically no good reason to
> put
> up with the compromises (lower Q and heat loss) that a toroid necessary
> involves.
>
> The big mistakes made on these are trying to use a single toroid for 2
> bands - as Carl says below, one toroid - one band. And not providing any
> consideration for heating if you are into high duty cycle modes like RTTY.
> You can find a lot of comments on both of these issues in the last couple
> of
> year message history.
>
> 73/jeff/ac0c
> www.ac0c.com
> alpha-charlie-zero-charlie
>
> -----Original Message-----
> From: Jim Brown
> Sent: Saturday, March 24, 2012 6:08 PM
> To: amps@contesting.com
> Subject: Re: [Amps] Guidelines.....toroids for tank ckts
>
> On 3/24/2012 3:24 PM, Carl wrote:
>> I would not recommend toroids above 40M and even there its iffy at high
>> power. And of course use one per band.
>
> Yes. I don't know anything about powdered iron materials, but all
> ferrites get increasingly lossy with increasing frequency. A few
> ferrite mixes are designed to handle high power, and are pretty low loss
> at low to medium frequencies, but each of them has a high frequency
> limit, beyond which their loss has increased to the point that they are
> not very useful. For example, Fair-Rite #61 starts getting lossy above
> about 10 MHz, while their #67 starts above 20-30 MHz. In general,
> losses will couple from the core to the wires, and will show up in the
> equivalent circuit as resistance.
>
> Another issue is voltage breakdown -- ferrites are semi-conductors, and
> each mix is different there too. Some are pretty good insulators, others
> are fairly conductive. It's worth studying the Fair-Rite catalog, which
> is really excellent. Fair-Rite data sheets include data for resistivity,
> permeability and permittivity. If you have a solid EE background, it's
> also worth calling Fair-Rite's technical support people. But study their
> catalog and applications notes first so that you know what questions to
> ask and can understand the answers.
>
> 73, Jim K9YC
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1424 / Virus Database: 2113/4891 - Release Date: 03/24/12
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|