Gary, Colin, Bob and The List:
I sent an explanation of my ignorance on that key
point and so far it has not been posted.
- JimT
----- Original Message -----
From: "Robert B. Bonner" <rbonner@qro.com>
To: "'Jim Tonne'" <tonne@comcast.net>; "'Tom W8JI'" <w8ji@w8ji.com>;
<w2cqm@juno.com>; <amps@contesting.com>; "'Norman Hockler'"
<sanorm@columbus.rr.com>
Sent: Friday, February 02, 2007 11:37 AM
Subject: RE: [Amps] How best to reduce filament voltage?
> Jim you missed the key issue this is a ONE TRANSFORMER does all situation.
>
> You fire up the high voltage and you don't want that resistor dimming the
> whole AMPLIFIER..
>
> BOB DD
>
> -----Original Message-----
> From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
> Behalf Of Jim Tonne
> Sent: Friday, February 02, 2007 9:51 AM
> To: Tom W8JI; w2cqm@juno.com; amps@contesting.com; Norman Hockler
> Subject: Re: [Amps] How best to reduce filament voltage?
>
>
> Tom wrote:
>
>> This will not work. Don't do it.
>
> in reply to
>
>>> Install a resistor on the primary side of the transformer.
>
> which is what I would have suggested.
>
>> It will totally hose the voltage regulation under load,
>
> The load is constant so "regulation" in the usual sense
> (same output voltage with varying load value) is not an
> issue. A series resistance would limit inrush. A series
> resistance at the transformer primary would limit inrush
> to the transformer as well.
>
>> the resistors would have to be huge.
>
> Seems to me the resistor WATTAGE value would be
> the same regardless of whether it was in the primary or
> the secondary of the filament transformer.
>
> Another way around this whole issue is to use a
> relatively small bucking voltage (obtained from, say,
> a filament transformer) in series with the transformer
> primary to reduce its input voltage. That would of
> course be very efficient. By putting a variac or
> equivalent on the primary of the buck transformer
> the filament voltage could be tweaked to perfection.
>
> - JimT
>
>
>
>
> ----- Original Message -----
> From: "Tom W8JI" <w8ji@w8ji.com>
> To: <w2cqm@juno.com>; <amps@contesting.com>; "Norman Hockler"
> <sanorm@columbus.rr.com>
> Sent: Friday, February 02, 2007 10:32 AM
> Subject: Re: [Amps] How best to reduce filament voltage?
>
>
>> This will not work. Don't do it.
>>
>>> Install a resistor on the primary side of the transformer.
>>> Much
>>> lower current and the resistors will act as a
>>> soft start for the filament to damp the inrush when you
>>> first turn on
>>> power. Set the resistor value with the
>>> tube on and warm There are many sliding tap resistors
>>> available from
>>> the distributors or a fixed one will
>>> work as well. Ohms law calculation to determine the value.
>>
>> It will totally hose the voltage regulation under load, and
>> the resistors would have to be huge.
>>
>> 73 Tom
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|