Amps
[Top] [All Lists]

SV: [AMPS] terminations that don't...

To: <amps@contesting.com>
Subject: SV: [AMPS] terminations that don't...
From: sm5ki@algonet.se (Hans Goldschmidt)
Date: Fri, 24 Sep 1999 19:56:00 +0200
I have been connecting my Cantenna to a long fence in the garden and got S9
reports from Finland. Works fine and nice swr too, hi!
----------
>Från: Skip S Isaham <nospam4me@juno.com>
>Till: amps@contesting.com
>Ämne: [AMPS] terminations that don't...
>Datum: ons 22 sep 1999 07.41
>

>
>Jim,
>I used a Kenwood TS-830 into a cantenna to heckle a good friend while he
>ran the west coast swap net on 40 meters. He lived about 2 miles away and
>50 watts would get over to his house just fine.
>It was a tremendous amount of fun to try and crack him up when no one
>past the few miles could here the comments.
>terminations don't...
>cheers
>skipp
>
>
>[snip]
>Hi,
>Last night while tuning up into the DL to work the
>3C0 (which I did, hooray),  I noticed I could hear
>a faint bit of rcv'd signal in the rig while connected
>to the DL,  not the antenna!  The antenna tuner unit
>was in the "Bypass" switch position to get to the DL.
>
>However,  I can also hear a faint active RF signal when
>the wafer switch in the antenna tuner is just set to
>Coax 2,  which in my case just goes to an unused
>antenna input 239 socket on the back of the tuner.
>Maybe this is just 60 to 80 dB down or more
>coupling between wafer switch contacts?  
>Top view down onto my tuner showing layout
>and two wafer antenna/DL switch can be seen at:
>
>    http://www.palstarinc.com/palmain.htm
>
>As I look at it,  the DL is a sort of shielded 50 ohm
>resistor connected between shield and center
>conductor of about 8' if coax to the unit sitting outside  
>in a container of silicon oil.  The container has fins to 
>dissipate any heat,  and the DL is rated to take a 
>couple of kW continuous   (Bird 8890 unit).
>
>Should the unit's shielding case be grounded to
>the station common ground point outside?  The
>DL is sitting out their just beside the ground
>rod and cold water service pipe to which the
>rod is also strapped with 1" wide braid.
>
>Would a 1" wide braid to the DL case be needed,
>wise,  or silly??
>73,  Jim,  KH7M
>
>
>___________________________________________________________________
>Get the Internet just the way you want it.
>Free software, free e-mail, and free Internet access for a month!
>Try Juno Web: http://dl.www.juno.com/dynoget/tagj.
>
>--
>FAQ on WWW:               http://www.contesting.com/ampsfaq.html
>Submissions:              amps@contesting.com
>Administrative requests:  amps-REQUEST@contesting.com
>Problems:                 owner-amps@contesting.com
>Search:                   http://www.contesting.com/km9p/search.htm
>
>

--
FAQ on WWW:               http://www.contesting.com/ampsfaq.html
Submissions:              amps@contesting.com
Administrative requests:  amps-REQUEST@contesting.com
Problems:                 owner-amps@contesting.com
Search:                   http://www.contesting.com/km9p/search.htm


<Prev in Thread] Current Thread [Next in Thread>