OK, this led me further to review the settings in WL and the COM ports.
I had to de-select COM1 from allocation to a rig for CW before the option
to select FSK in MMTTY is available.
Joe/Mork lead me to RTTYrite which revealed the the COM1 port was in use
and thus not able to be selected.
I guess I'll have to flip the switch if I want to run a CW keyer on the
computer or RTTY.
Thanks for the pointers Mork and Joe :)
On Fri, 07 May 2010 16:47:06 -0400, "Joe Subich, W4TV" <lists@subich.com>
wrote:
>> I have the FSK interface connected to COM1 on the laptop dock (real
> > DB-9).
>
> If the port on the dock appears as COM1 in Windows, set RTTYrite for
> COM 1 before you open the MMTTY set-up within the plug-in. That should
> enable FSK on COM1.
>
> 73,
>
> ... Joe, W4TV
>
> On 5/7/2010 3:48 PM, Larry 'Rebar' Rebarchik - N6CCH wrote:
>> Joe,
>> I have the FSK interface connected to COM1 on the laptop dock (real
>> DB-9).
>> As noted before, the setup works fine with MMTTY running standalone,
but
>> not with WL and the plug-in.
>>
>> I'll dig around a bit more.
>>
>>
>> rebar
>> On Fri, 07 May 2010 15:34:09 -0400, "Joe Subich,
W4TV"<lists@subich.com>
>> wrote:
>>>> I have a laptop docked with Rig Control on COM9 via USB/Serial
>>> > and FSK on COM1 via<http://www.w3yy.com> FSK/CW interface box
>>> > <http://www.w3yy.com/fsk.htm>
>>>
>>> WriteLog only supports FSK on COM1-COM8. That limitation also
>>> applies to the MMTTY plug-in since the FSK port is set by the
>>> WriteLog RTTY Window when the "TU" (MMTTY plug-in) is started.
>>>
>>> Since you are using the W3YY interface, I assume it is being
>>> driven by a USB to serial adapter. You will need to configure
>>> RTTYrite to do "Software generated FSK" on the USB port and
>>> make sure that port is in the COM1 - COM8 range.
>>>
>>> You hardware supplier should be providing this support ...
>>>
>>> 73,
>>>
>>> ... Joe Subich, W4TV
>>> microHAM America, LLC.
>>> http://www.microHAM-USA.com
>>> http://groups.yahoo.com/group/microHAM
>>>
>>>
>>> On 5/7/2010 2:10 PM, Larry 'Rebar' Rebarchik - N6CCH wrote:
>>>> I've begun to get some more features sorted out with my K3 and have
>>>> discovered that the MMTTY Plug-in for WL does not have the ability to
>>>> select SOUND-COM when working in a FSK setup, the last two radio
>> buttons
>>>> are grey'd out in the setup control panel under WL when running MMTTY
>>>> [RTTY
>>>> Window].
>>>>
>>>> Has anyone else discovered this, or am I missing some special
>> selections
>>>> in my configuration to make this work?
>>>>
>>>> I have a laptop docked with Rig Control on COM9 via USB/Serial and
FSK
>> on
>>>> COM1 via<http://www.w3yy.com> FSK/CW interface box
>>>> <http://www.w3yy.com/fsk.htm>
>>>>
>>>> The WL/PC generated CW is working just fine, however, I cannot seem
to
>>>> get
>>>> the RTTY signals to the K3 rig.
>>>>
>>>> MMTTY v1.66G in standalone mode keys the rig just fine.
>>>>
>>
--
73 de N6CCH aka Rebar
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|