Ed, noting Jon Zaimes ref. to his use of 1/2" double braided poyester (AKA
Dacron), 7,000 lb mfr test, if you decide to go that route, my other
company, DAVIS ROPE and Cable Assembly, not to be confused with my DAVIS RF Co,
has this rope at very low pricing, Made in USA. Just contact me directly. 73,
Steve Davis, K1PEK
________________________________
From: TowerTalk <towertalk-bounces@contesting.com> on behalf of
towertalk-request@contesting.com <towertalk-request@contesting.com>
Sent: Monday, May 24, 2021 12:00 PM
To: towertalk@contesting.com <towertalk@contesting.com>
Subject: TowerTalk Digest, Vol 221, Issue 25
----------------------------------------------------------------------
Message: 1
Date: Sun, 23 May 2021 19:58:55 -0400
From: "Jon Zaimes" <jz73@verizon.net>
To: <ed_richardson@shaw.ca>, <TowerTalk@contesting.com>
Subject: Re: [TowerTalk] Mast Lifting
Message-ID: <070401d7502f$978e0130$c6aa0390$@verizon.net>
Content-Type: text/plain; charset="us-ascii"
Ed,
We use a capstan winch at the ground and 1/2" double braid polyester rope
(rated for 7000 pounds) to lift a mast. At the top of the tower we place a
2.5" rescue pulley several feet above the attachment point to the mast, just
above the rotor. In tight quarters I have a smaller pulley in the bag.
Two 3/8" saddle clamps are placed on the mast just above a bearing or
bushing or the tower top, as a safety measure. Lifts are done in short
increments with the clamps being moved every foot or two.
A saddle clamp also is used just above the rope attachment so the rope can't
slip up the mast.
Three kayak straps are used to keep the mast centered in the tower, unless
there's an extra bearing plate above the rotor to take care of this.
Using the winch at ground level (with my son Adam N3TTT there) is better
control than using a come-a-long locally at the top of the tower, and keeps
the climber's hands (mine) free for other things. We use GMRS radios to
communicate so there's no chance to be drowned out by the neighbor's lawn
mower (they seem to know when we're coming).
73/Jon
Jon P. Zaimes, AA1K
Tower climber for hire
http://www.aa1k.us/
Cell: 302-632-2353
Reviews of AA1K tower work on eham website:
http://www.eham.net/reviews/detail/12922
Hug your favorite tower every day, and always stay connected to it.
-----Original Message-----
From: TowerTalk <towertalk-bounces@contesting.com> On Behalf Of
ed_richardson@shaw.ca
Sent: Sunday, May 23, 2021 5:29 PM
To: TowerTalk@contesting.com
Subject: [TowerTalk] Mast Lifting
Needing to service the rotator and want to lift the loaded mast up and out
of the rotator bracket. I have used a cheap com-along in the past but I am
now reading that come-alongs are not suitable for lifting and lowering
loads, they are intended for horizontal movements only.
A lever hoist would seem to be the appropriate tool.
So what are the tower experts using for this task? The dead weight would be
approximately 350 lbs plus any resistance/friction.
Any recommendations? Safety outweighs cost.
Ed ve4vt
_______________________________________________
_______________________________________________
------------------------------
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|