Yes, this is by far the easiest and a very effective method. I find it is
easier to cut the slots opposing each other (180 degrees) and at a depth
just slightly larger than the width of the SS hose clamp. That way if two
slots don't get the job done, two more cuts can be made and they will all be
90 degrees apart.
73, Ted W4NZ
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com]On Behalf Of Gene Fuller
Sent: Thursday, September 23, 2010 9:50 AM
To: Roger; towertalk@contesting.com
Subject: Re: [TowerTalk] securing loose element ends
I may be missing something here, but when I make an element, if the clamp
doesn't quite firm up the joint I just get the hack saw out and cut another
slot, 90 degrees around the circumfrence from the first and that allows for
a bit more compression and preserves the potential for further length
adjustment.
Gene / W2LU
----- Original Message -----
From: "Roger" <roger@rogerhalstead.com>
To: <towertalk@contesting.com>
Sent: Thursday, September 23, 2010 12:52 AM
Subject: Re: [TowerTalk] securing loose element ends
> On 9/23/2010 12:25 AM, Kevin Normoyle wrote:
>>
>>>> Hi TT'ers,
>>>> I was putting together my Hygain Ex 14 today and found something I
>>>> hadn't expected. When tightening up the hose clamps to secure the
>>>> ends of the elements (7/16") that regardless of how hard I cranked
>>>> the clamps, the tips were still loose enough that they could easily
>>>> be pulled out-maybe 10# of pressure!
>>
>> I like rivets. But I think there's a different issue here. Rivets are
>> nice for telescoping straight tubes that fit
>> nicely within each other. And
>>
> As do I, but they will also work with properly swaged and fitted elements.
>
>> in fact I just ordered a bunch of Avex rivets from Aircraft Spruce,
>> because I was getting too many mandrels breaking off
>> on some Pop Rivet brand rivets. I read good things about the Avex rivets,
>> but haven't used them yet. Interestingly they
>> have a wider grip range than the Pop Rivet ones I was using.
>
> I think you will find the piece that fits into the tool (I've forgotten
> the name of it) has barbed like edges, almost like a bee's leg. These
> expand the gripping range. "I think" (meaning I don't remember for
> sure) they are also "blind rivets" so moisture will not go through them.
>
> What rivets do other people use? I also switched to a
>> different rivet tool.
>> http://www.aircraftspruce.com/catalog/hapages/avexblindriv.php
>>
> I don't think the tool will make a great deal of difference if it fits
> correctly and works the way it's supposed to.
>
>> But the problem with Hygain, is the joints are swaged. And the swage is
>> not that precise, so you don't get good contact
>> on hte inner surfaces.
>
> A swaged joint "can be precise", but the dies wear and they are
> expensive so manufacturers get every last mile out of them.
>>
> I've thought of trying this, but on a larger scale using rollers on
> larger tubing. The problem with swaging or working Aluminum is the
> stuff work hardens FAST. But at-any-rate, Those who have worked with
> lathes are probably familiar with the hand held knurling tool. It's
> hinged at the outer end, then back in a ways are two wheels on one side
> and one on the other. The piece to be knurled is held in and turned by
> the lathe. The knurling tool is placed over the tube with pressure
> applied to the handles, impressing the knurl into the Aluminum surface.
>
> If the rollers were replaced with smooth rollers the tool could be used
> to compress the swaged end of the element. Carefully done the entire
> swaged end could be smoothly compressed to fit snugly on the inner
> section. This would have to be done carefully and only a few thousandths
> at a time, but should work. OTOH it's going to a lot of work for a
> little gain. Me? I'd think it's worth it, but it's certainly not worth
> the expense of going out and purchasing a lathe and the tools to go with
> it. <:-))
>
>
>>
>> Plus: as I noted here before, the clamps Hygain ships are no good. They
>> are cheapest of the cheap and will strip easily.
>> I will bet two cents there is no recognizable manufacturer name on the
>> clamps. (look)
>>
>> So: you want better clamps, so you can get more torque without stripping.
>> And you might want to double clamp just
>> because the swaging is bad.
>>
>> Maybe someone can comment about whether they've riveted the slit Hygain
>> swaged ends. I would think it wouldn't work as
>> well as normal telescoping tubing.
> I've had good luck with the Hy-gain joints and connectors, but the last
> ones I used were nearly 5 years ago. The looked a bit "tent like" made
> of SS strip, with a screw in the center. I've never stripped one of
> those but I sure have stripped a bunch of the SS hose clamps. I don't
> know what they use now that they've been "bought out".
>>
>
> 73
>
> Roger (K8RI)
>> -kevin
>> AD6Z
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|