I think you mis-read my post. Grease is a form of oil is what I was
referring to. I'd only use grease on a non-sealed system, unless I wanted to
lube it once a week. I remember being taught by an ex-LAPD SWATdog... my
1911 had been lubed with oil only two weeks before the class, then laid in
the safe; he had some interesting incenuations to speak of when he noticed
my gun running dry within the first 50 rounds of class.
Not sure about the 10w50... I'd imagine you'd have a nice pool of 10w50 at
the bottom of the T2X (assuming it's not going to leak out the base). My
basis is when thinking of firearms, engines, etc. I use 15W40 for my diesel
and need the assistance of a pump to spread the oil around the engine, after
gravity has drained it to the sump. My lawn mower relies on the oil being
splashed around to lubricate itself. My guns drain oil to the lowest point
(I've switched to TW25B (elephant sperm as an ex-Delta operator taught me
during a course)) which is a grease.
To sum it up, buy a quality grease that won't dry out too quickly... but I
still have to regrease/pack wheel bearings and my firearms on a consistent
basis. It made me laugh about the rotor being dry after 30 years... I mean,
what grease would I honestly expect to hold up that long?
On 4/10/10, WA3GIN <wa3gin@comcast.net> wrote:
>
> thanks... I'm leaning towards oil as well...I've open up several rotors
> over
> the years... bearing all rusted with grease packed inbetween. The grease
> just doesn't protect them at all as best I can tell. Maybe 3&1 is too light
> of an oil but 10W50 might work fine...
>
> ----- Original Message -----
> From: "Timothy Coker" <n6win73@gmail.com>
> To: "Tower and HF antenna construction topics." <towertalk@contesting.com>
> Sent: Saturday, April 10, 2010 4:40 PM
> Subject: Re: [TowerTalk] Tailtwister Rotor Rehab Question
>
>
> >I am sort of an oil guy... I guessed the blue grease was a lithium based
> > marine grease. Looked and felt a lot like what I used for my marine
> > trailer's bearings. I could of course be wrong... not exactly like I sent
> > it
> > off to be tested.
> >
> > On Sat, Apr 10, 2010 at 1:38 PM, Roger (K8RI)
> > <K8RI-on-TowerTalk@tm.net>wrote:
> >
> >>
> >>
> >> WA3GIN wrote:
> >> > Hi folks,
> >> >
> >> > Rebuilding the old Tailtwister. Ballbearing look good but the grease
> >> > is
> >> hard and useless, not protecting the bearing much. I used 3&1 oil to
> >> clean
> >> the bearings and races but wonder if I should just leave the 3&1 or
> >> slather
> >> the bearing with white lithium grease.
> >> >
> >> That's what I'd use. Others say different, but I'll bet you find the
> >> blue grease Norn's uses is similar.
> >> Also, there's something wrong if a rotator is picking up particles out
> >> of the air.
> >>
> >> 73
> >>
> >> Roger
> >> > Recommendations welcome. Please respond direct.
> >> >
> >> > 73,
> >> > dave
> >> > wa3gin
> >> > _______________________________________________
> >> >
> >> >
> >> >
> >> > _______________________________________________
> >> > TowerTalk mailing list
> >> > TowerTalk@contesting.com
> >> > http://lists.contesting.com/mailman/listinfo/towertalk
> >> >
> >> >
> >> _______________________________________________
> >>
> >>
> >>
> >> _______________________________________________
> >> TowerTalk mailing list
> >> TowerTalk@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/towertalk
> >>
> > _______________________________________________
> >
> >
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|