Towertalk
[Top] [All Lists]

Re: [TowerTalk] Plugs G-800

To: "Tower and HF antenna construction topics." <towertalk@contesting.com>
Subject: Re: [TowerTalk] Plugs G-800
From: "larryjspammenot@teleport.com" <larryj@teleport.com>
Reply-to: "larryjspammenot@teleport.com" <larryj@teleport.com>, "Tower and HF antenna construction topics." <towertalk@contesting.com>
Date: Tue, 26 Jan 2010 20:05:39 -0800 (GMT-08:00)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
I, too, need one of the plugs for my Yaesu G800DXA rotator (the rotor end, not 
the controller). When you order a plug for it, does it come with any kind of 
"boot" or other weatherproofing system to keep water out of the contacts? Or do 
you just have to apply lots of "Coax-Seal" or some other similar material all 
over it and hope for the best?

LJ 


-----Original Message-----
>From: Perry - K4PWO <k4pwo@comcast.net>
>Sent: Jan 26, 2010 7:25 PM
>To: "Tower and HF antenna construction topics." <towertalk@contesting.com>
>Subject: Re: [TowerTalk] Plugs G-800
>
>R&L Electronics has the NJC-207-PF connectors for $20 each.
>See... http://www.randl.com/cgi-local/cart/cart.cgi?cart=ai&ID=39808
>
>73 de Perry - K4PWO
>
>--------------------------------------------------
>From: "Terrence R. Redding Ph.D." <terry@oltraining.com>
>Sent: Tuesday, January 26, 2010 06:49 AM
>To: <towertalk@contesting.com>
>Subject: Re: [TowerTalk] Plugs G-800
>
>> Jim, thanks for the comment.
>> 
>> Yes, the new rotor motors ship with the seven pin male connector on the
>> motor.  The older motor has a larger six pin plug.
>> 
>> I am looking for a source of both.  If none are known, then I will call
>> Yaesu.
>> 
>> Terry - W6LMJ
>> 
>> 
>> On 1/26/10 1:58 AM, "towertalk-request@contesting.com"
>> <towertalk-request@contesting.com> wrote:
>> 
>>> On Tue, 26 Jan 2010 00:14:05 -0500, Terrence R. Redding Ph.D. wrote:
>>> 
>>>> I am wondering if there is a source for the six pin and seven
>>>> pin female connectors that attach at the rotor motor end of the
>>>> rotor control cable?
>>> 
>>> I'm looking at schematic in the Yaesu manual for the rotor I bought
>>> new this summer. The part numbr for the connector attached to the
>>> rotor is NJC-207-RW. The cable-mounted connector that mates with it
>>> is NJC-207-PF. At the time, I looked at the connectors and decided
>>> that they were Japanese parts, but I did not recognize a mfr.
>>> 
>>> The same manual also includes schematics for the G-2800DXA. The
>>> corresponding connectors for that rotor are designated NJW-207-RW
>>> and NJW-207-PF. I've not seen a G-2800DXA, so don't know the
>>> difference between the connectors.
>>> 
>>> The connectors for both rotors are 7-pin connectors.
>>> 
>>> 73,
>>> 
>>> Jim K9YC
>> 
>> 
>> _______________________________________________
>> 
>> 
>> 
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>> 
>_______________________________________________
>
>
>
>_______________________________________________
>TowerTalk mailing list
>TowerTalk@contesting.com
>http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>