I have tried modelling this beast, and can get reasonable numbers, but I don't
really trust the connection between the model and the real world, due to the
trap design. Most modelling programs cannot handle the small dimensions of the
inductive portions of the traps.
As a long time KT-34(6)XA fan, I have collected bits and pieces of information
on the design.
Pasted below re some notes from the designer on tuning for specific instances,
which may help you out. Note that they refer to A,B,C, and D dimensions which
come from the original KLM instructions.
A is the distance from the outer center strap to the tip.
B is the distance from the outer center strap to the outer shorting strap.
C is the distance from the inner shorting strap to the farthest inside
conductor.
D is the distance from the center section tip to the end of the 10 meter
capacitor.
(this is vague, but I can clarify or post a picture somewhere from the original
instructions)
====quote pasted here====
KT34A and KT34XA
VSWR High on Low End of 15M?? The tuning of the reflector controls the VSWR on
the Low End of each band. The "B' Dimension tunes the 15 meter resonance of
each element. Sometimes It is difficult to look at the VSWR curve and determine
if the reflector has moved up or dawn in frequency. Try shortening the
reflector "B" Dimension by 1". If the Low End VSWR improves. you can move the
"B" Dimension as much as 3 inches without having much effect on 20 meters. If
shortening makes the condition worse. then put "S" as long as possible and
extend the 'ID" Dimension up to 2" as required. The 'D" Dimension also effects
10 and 20 meters slightly so check for satisfactory VSWR on those bands.
VSWR High on the Low End at each Band? If you have High VSWR on the Low End of
each band, check the color of your capacitor caps. It they are black, contact
KLM and a Capacitor Kit will be send to you tree of charge. Follow the
instructions in the kit and it should correct your Low End VSWR problem. If you
already have white or light green capacitor caps and you have Low Band edge
VSWR problems, remember, the reflector controls the Low End. Start with 10
meters "C" Dimension on the reflector. Adjust as required to improve the VSWR;
1 to 1+" adjustment should be the most you should change the "C" Dimension.
Next check 15 Low End VSWR. If it's still high, adjust the "B" Dimension. The
"A" Dimension controls 20 exclusively . Remember, you should not adjust the
VSWR if it is poor only pointing the antenna in one or two directions. This
indicates a problem outside the antenna created by another structure.
VSWR High on High End of 1OM/15M/2OM? If you have High VSWR on the High End of
all three bands, start your adjustments on 10 meters as correcting 10 will also
improve each band. The "C" Dimension controls 10 meters. Usually the High End
has moved down slightly so shortening the"C" Dimension by as much as 1 inch may
be required. Next check 15 meter High End again. If the VSWR is still High,
shorten the "B" 1 to 3 Inches as required. Normally,. when 10 and 15 are
correct. 20 will also be right but if needed the "A" Dimension can be adjusted
as necessary.
What does the "A" after the KT-34 and XT-34x mean? About 1 year after we
started making the KT-34 and KT-34x. we chanced the boom wall thickness. For
upgrade and repair purposes only~ we designated the change with the letter "A"
after KT-34 and KT-34X so we could ship the correct replacement parts. No
tuning. dimension, or other part chanqe is connected with the "A" suffix.
VSWR High when it rains? Several things can cause this. Before blaming the
antenna, make sure the feedline is riot the culprit. If the feedline is okay.
then it may be in the capacitor sections of the antenna. Polyethelene capacitor
caps my be cracked or dislodged allowing drops of water inside the capacitor.
It only takes one drop to have severe effects on the VSWR. If no caps appear
dislodged or cracked. then water may have been blown into one or more of the
the capacitor vent holes. This usually occurs only if the antenna hangs over
the edge of a building or a cliff where high velocity updrafts can occur and
drive droplets of water upand into the vent holes. Vent hole covers can be
obtained upon request from KLM. If water has been blown into the vent holes,
the High VSWR condftion will usually correct Itself In a day or two. If it does
not correct itself. it means there my be other problems. If high power was used
during the rain, induced high VSWR condition arcing may have occured inside the
capacitor and a carbon path may still exist. Director Dl usually sees the
Highest voltage during operation and the arcing will normally occur at the
junction of the 10 and 15 meter capacitor tubes near where the "A" straps are
attached to the capacitor tubes. This element can be reached and removed fran
the boom for repair without disturbing the rest of the installation.
VSWR High across 15M; okay on 10 and 20 after rain? This probably means water
is inside the 15 meter capacitors. Check for cracked or dislodged capacitor
caps. 15 meters has the highest Q elements and therefore is the most sensitive
to disturbances. If the antenna is located where high winds can drive moisture
into the vent holes of the capacitor caps, contact KLM and a set of snap-on
vent hole covers can be obtained.
How close can I stack a 40M beam? 40 meter horizontally polarized antennas
Usua1ly disturb 15 meters the most because of the harmonic relationship. To
minimize this when stacking 40 and 15 on the same tower, orient the 40 meter
antenna at a direction 90 degrees from the tribander. Stacking should not be
closer thin 6 feet with a two element forty and further If 40 is more than 2
elements.
How close can I stack a 2M beam? Usually the 2 meter beam will not affect the
tribander. The two meter beam should be at least 1/2 wavelength (40 Inches) any
from the tribander and further if possible. The larger t'n 2 meter antenna. the
more it may be affected.
How close can I stack a 40M Dipole at 90*? As close as 3 to 4 feet as long as
it rotates with the tribander and is not fixed to the tower. such as a wire
inverted V might be.
How far should the beam be from the ground? At about 1/4 wavelength at the
lowest frequency (16 feet at 20M) the antenna will begin to exhibit reasonable
performance but. of course. the angle of radiation will be almost straight up
so not much DX will be easily worked. At a 1/2 wavelength (32 ft.) up there is
a real improvement. Recommended height for excellent performance is 45 feet or
higher.
How much potwer can the 34 handle? All you can legally muster and then some.
Lossless elements and good design have been used to virtually eleminate any
power handling problems. If, however. your VSWR goes high for any reason
running high power may only cause further damage.
Can the 34 be peaked for even greater gain on one portion of the band? Yes. but
only .2 to .3db and at a huge sacrifice to all other performance aspects of the
rest of the antenna. A high degree of interaction from band to band occurs in
any tribander & gain may be severely affected on the other bands. The KT-34A
and KT-34XA were designed with max gain as the top priority and it's unlikely.
without a good antenna range. any further overall improvement can be made even
by narrowing banding
Can you add a 4OM dipole to the end of a 34? Not without the possibility of
disturbing the performance of the 34A or 34XA. If you try it anywhere, put it
behind the reflector by six (6) or more feet. The recommended spot for a
rotatable 40 meter dipole is above or below the tribander by 3 to 6 feet and in
line with the boom. This should eliminate any noticeable interaction.
how much power will the balun take? The balun Is rated at 4KW peak envelope
power (PEP). It can take more for short periods but core saturation may occur
causing severe overheating and loss of balance. Non-linearity can also occur
perhaps generating spurious or harmonic responses.
How tight can the insulator clamp be tightened? Tests run at the factory show
the clamp, when properly lubricated. can actually compress the boom material
noticeably before failing. Normal tiqhtening by hand with a spintite or small
socket wrench is adequate and a hole in the clamp is provided to pin it after
proper alignment has been achieved. During initial assembly. we recomend
retightening after one over-night temperature cycle.
How come the F/B is lower than other beams? The KT-34A has excellent
front-to-'back for a tribander. Monobanders may be a bit better. The KT-34XA
was designed specifica1ly for maximum gain on each band. Front-to-back was
certainly a consideration but not at the expense of gain, which rivals or
exceeds many monobanders its size or larger.
How hard is the 34 to tune? Normally the KT-34A and XA are "tuned during
assembly by setting the parts to specific called out Dimensions so no tuning
should be required. If tuning Is required. It is not difficult if you know two
things. The Reflector has the most control over VSWR at the Low End of the band
and the Director Dl (right in front of the Front Driven) controls the High End.
The "C" Dimension sets 10 meters. "B" sets 15 meters. and "A" Dimensions sets
up 20 meters.
How long does It take to put it together? Reports back from users indicate as
litt1e as four hours and.as much as forty hours. Typically eight to ten hours
for the first time with a 34A and ten to twelve hours for the XA. The
instructions have many detailed pictures Common sense, pictures, and dimensions
are all you should really need but much more is provided in the Assenbly
Manual.
How far apart in order to phase two 34's? The 34A's could be stacked at 22 to
30 feet apart and XA's 36 to 45 feet apart.
What is the best height for the 34? The Lowest band usually suffers the most at
low heights. In order for 20 meters to do the best job. it should be up 45 feet
or more. Over 120 feet is questionable because performance may not be optimum
when the band is wide open. A lower height might be better. 60-70 feet is
probably optimum for most applications.
Do power lines effect the performance? Yes. but a lot depends on their height
and and distance from the antenna. To make a crude check for interaction. check
the VSWR with the antenna pointed in a clear direction. Then rotate the antenna
towards the power lines. If VSWR changes. interaction is occurring with some
probable performance degradation.
How come the non-driven elements are not grounded? They can be but the element
mounting insulator KLM uses is designed for maximun versitility of element
mounting and testing. Keeping it insulated from ground maximizes this
capability. If grounding is desired. a simple connection from the center of the
middle jumper strap to the boom is sufficient. This jumper to ground at the
middle will not affect performance or VSWR.
What is the advantage of no traps? The KT-34A and XA really do have traps but
our construction is simply not straight forward. Using linear loading in place
of a coil greatly reduces coil losses and the linear loading portion also
radiates far better than a coil. Our capacitors use air as the basic dielectric
which requires that they be large but their Q is extremely high. All this adds
up to no heating of components which means more power is radiated.
Can the KT be painted? Yes. but we recommend several things first. Put the
antenna up and be sure it is working correctly on all bands. If possible. leave
it up a few days so the alininwi oxidizes slightly This should make the paint
stick better.
KLM Electronics, Inc. PO Box 816 Morgan Hill, CA 95037 (408)779-7363
====end of quote===
73 de Tony, K1KP
--------------------------------------------------------------------------------
Copyright © 1997-2000 All Rights Reserved
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|