Towertalk
[Top] [All Lists]

Re: [TowerTalk] Rohn 20G Tower lay down questions

To: "RICHARD BOYD" <ke3q@msn.com>, "Don M" <hy_tek@hotmail.com>,<towertalk@contesting.com>, <ersmar@comcast.net>
Subject: Re: [TowerTalk] Rohn 20G Tower lay down questions
From: "K8RI on Tower talk" <k8ri-tower@charter.net>
Date: Wed, 12 Oct 2005 17:55:15 -0400
List-post: <mailto:towertalk@contesting.com>
----- Original Message ----- 
From: "RICHARD BOYD" <ke3q@msn.com>
To: "Don M" <hy_tek@hotmail.com>; <towertalk@contesting.com>; 
<ersmar@comcast.net>
Sent: Wednesday, October 12, 2005 4:17 PM
Subject: Re: [TowerTalk] Rohn 20G Tower lay down questions


>I know half a dozen of us raised a Rohn 25, 50' tall as I recall, with a 
>TA-36 tribander and a couple VHF antennas on top, walked it up.  I was 
>surprised that it wasn't harder than it was.  We probably could have done 
>it with less men.  We did have a pickup truck attached to it for the last 
>bit, once we had raised it high enough that it was hard for us to push it 
>up further.  The truck took over.

We did an old 50' American Steel (2 bolt). Instead of the truck we just used 
an extension ladder to push, as a lever when we could first get it under and 
in.  Then we just continued to use it to push when the angle was such that 
the tower would have been at its heaviest for the guys underneath.  It 
worked very well.

You do have to be careful not to get the leg of the ladder stuck between 
braces in the tower so with a ROHN you'd have to insert the ladder between 
sections.

(Don't use Aluminum ladders around power lines)

Roger Halstead (K8RI and ARRL 40 year Life Member)
N833R - World's oldest Debonair CD-2
www.rogerhalstead.com
>
> It seems to me your point of lowest mechanical advantage (greatest 
> mechanical disadvantage) in lowering it is at the beginning, 'til it gets 
> down within easier reach of you and your helpers.  But for that tower, a 
> decent (not string or twine but it wouldn't have to be super heavy) rope 
> over the house or some other high point, should easily take care of it.
>
> 73 - Rich, KE3Q
>  ----- Original Message ----- 
>  From: ersmar@comcast.net<mailto:ersmar@comcast.net>
>  To: Don M<mailto:hy_tek@hotmail.com> ; 
> towertalk@contesting.com<mailto:towertalk@contesting.com>
>  Sent: Wednesday, October 12, 2005 12:20 PM
>  Subject: Re: [TowerTalk] Rohn 20G Tower lay down questions
>
>
>  Don:
>
>       Regardless of what folks tell you about lowering the tower, do NOT 
> use the chimney as a pulley support.  Chimneys might not be part of the 
> house structure.
>
>       One of my summer jobs in college was for a brick mason.  We laid 
> brick for homes, including chimneys.  Exterior brick chimneys (those that 
> appear to run up along an outside wall of a residence) are nothing more 
> than three sides of brick laid up around the central flue liner (the 
> yellowish core sticking up through the tops of most modern chimneys.) 
> These brick layers are connected to the house wall by nothing more than 
> corrugated steel straps cemented between the brick courses and nailed to 
> the walls.  (Sometimes I cringe at TowerTalkians' suggestions for mounting 
> rotating HF arrays atop chimneys.)
>
>       Caveat Amateur.
>
>  73 de
>  Gene Smar  AD3F
>
>
>
>  > I currently have a Rohn 20G tower which consists of 2 - 10'  and 1 - 9' 
> top
>  > sections about 29' tall overall not including antenna. It has a hinged 
> base
>  > which enables the tower to be layed over to the ground. I need to 
> rework the
>  > top mast section which is rusted and prevents me from replacing the 
> mast.
>  > How difficult is it to lay this tower down? Can it be done by just 
> having 3
>  > men or so walk it down or is it too heavy to do it that way. I can run 
> a
>  > guide rope from over my brick chimney which is about half way up for 
> added
>  > support while lowering. The weight of the mast and antenna is nominal. 
> From
>  > what I've read the weight of the 20G tower sections adds up to about 90
>  > pounds total. Since I was not here when the tower was installed I have 
> no
>  > idea of the difficulty in laying it over manually. Can this be done? 
> Thank
>  > you.
>  >
>  >
>  > Don
>  >
>  >
>  > _______________________________________________
>  >
>  > See: http://www.mscomputer.com<http://www.mscomputer.com/>  for "Self 
> Supporting Towers", "Wireless Weather
>  > Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any 
> questions
>  > and ask for Sherman, W2FLA.
>  >
>  > _______________________________________________
>  > TowerTalk mailing list
>  > TowerTalk@contesting.com<mailto:TowerTalk@contesting.com>
>  > 
> http://lists.contesting.com/mailman/listinfo/towertalk<http://lists.contesting.com/mailman/listinfo/towertalk>
>  _______________________________________________
>
>  See: http://www.mscomputer.com<http://www.mscomputer.com/>  for "Self 
> Supporting Towers", "Wireless Weather Stations", and lot's more.  Call 
> Toll Free, 1-800-333-9041 with any questions and ask for Sherman, W2FLA.
>
>  _______________________________________________
>  TowerTalk mailing list
>  TowerTalk@contesting.com<mailto:TowerTalk@contesting.com>
> 
> http://lists.contesting.com/mailman/listinfo/towertalk<http://lists.contesting.com/mailman/listinfo/towertalk>
> _______________________________________________
>
> See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless 
> Weather Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with 
> any questions and ask for Sherman, W2FLA.
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk 
_______________________________________________

See: http://www.mscomputer.com  for "Self Supporting Towers", "Wireless Weather 
Stations", and lot's more.  Call Toll Free, 1-800-333-9041 with any questions 
and ask for Sherman, W2FLA.

_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>