Topband
[Top] [All Lists]

Re: [CQ-Contest] [TowerTalk] RG-6 connector issues/ rcv array

To: "'W3YY'" <w3yy@cox.net>, "'Mike Fatchett W0MU'" <w0mu@w0mu.com>,<cq-contest@contesting.com>, <towertalk@contesting.com>,<topband@contesting.com>
Subject: Re: [CQ-Contest] [TowerTalk] RG-6 connector issues/ rcv array
From: "Tim Duffy K3LR" <k3lr@k3lr.com>
Reply-to: k3lr@k3lr.com
Date: Fri, 18 Jan 2008 20:49:03 -0600
List-post: <mailto:cq-contest@contesting.com>
Hello Bob!

I installed a four square receiving system for 160 meters using the RG-6
cable, connectors, stripper and installation tool all purchased from DX
Engineering. I installed a connector in less than 30 seconds with these
tools. It was easy to use. Everything went together without a problem and
has been in use for 2 years. No problems at all with the connectors. I am
very confident about my installation.

Did you use the DX Engineering RG-6 stripper?

73!
Tim K3LR

http://www.k3lr.com
K3LR DX Cluster telnet://dx.k3lr.com
 

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of W3YY
Sent: Friday, January 18, 2008 7:52 PM
To: 'Mike Fatchett W0MU'; cq-contest@contesting.com;
towertalk@contesting.com; topband@contesting.com
Subject: Re: [TowerTalk] RG-6 connector issues/ rcv array

Mike -

Are you using the connectors, crimp tool, and cable supplied by DX
Engineering?  I have their crimp tool and connectors but found them very
hard to use and was not confident about the resulting installation.  In
defense of DX Engineering I have not contacted them and discussed the issue,
I just gave up and used the RG-6 connectors I'm used to.  Just curious what
you're using.

73, Bob - W3YY

-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Mike Fatchett W0MU
Sent: Friday, January 18, 2008 10:46 PM
To: cq-contest@contesting.com; towertalk@contesting.com;
topband@contesting.com
Subject: [TowerTalk] RG-6 connector issues/ rcv array

Just a heads up.  I was having some problems with my 4sq receiving array and
found that the coax was pulling back from the connectors so that there was
no contact being made.  These were on high quality cable and the compression
connectors.  I built this antenna when it was warm.  It is now very cold and
been below zero.  I wonder if that has anything to do with this issue.  

Hopefully now I will see some better performance out of the array.

I also found that one of my ground had been removed, probably by the horses.


Mike W0MU

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________
CQ-Contest mailing list
CQ-Contest@contesting.com
http://lists.contesting.com/mailman/listinfo/cq-contest

<Prev in Thread] Current Thread [Next in Thread>