Hello Howard,
many thanks for detailed information about V3.033xe f/w rev.
Do you know anything more about the audio popping issue with this V3.033xe
mentioned
here...?
http://lists.contesting.com/_tentec/2016-10/msg00152.html
I will be happy to know if it was fixed finally.
73 - Petr, OK1RP
On Fri, Jul 26, 2019, at 6:00 PM, tentec-request@contesting.com wrote:
> Send TenTec mailing list submissions to
> tentec@contesting.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.contesting.com/mailman/listinfo/tentec
> or, via email, send a message with subject or body 'help' to
> tentec-request@contesting.com
>
> You can reach the person managing the list at
> tentec-owner@contesting.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of TenTec digest..."
>
>
> Today's Topics:
>
> 1. Latest fw revisions for 566 (Howard Smith)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Thu, 25 Jul 2019 16:19:25 -0500
> From: Howard Smith <jhsmith1024@gmail.com>
> To: tentec@contesting.com
> Subject: [TenTec] Latest fw revisions for 566
> Message-ID: <d304afbd-7a7c-08d9-9043-77ebdec2de5d@gmail.com>
> Content-Type: text/plain; charset=utf-8; format=flowed
>
> Hi Petr,
>
> This is the list of changes for the Orion II (566) firmware, Version
> V3.033xe:
>
> 2015-12-22Version V3.033xe
>
> ==============================================
>
> For this release, it is necessary to do the full Master Reset/RAM Clear
> sequence after the
> firmware is updated.
>
> 1. Download the new installer update file, which will force a Master Reset.
> 2. Power Down radio.
> 3. Perform a Master Reset.
> 4. Power Down radio.
> 5. Perform a RAM Clear.
> 6. Power Down radio.
> 7. Perform a Master Reset.
> 8. Power Down radio.
> 9. Power Up radio, and ready to use.
>
> Changes include:
>
> These changes apply to the Main Rx only. The Sub Rx was not changed.
>
> 1-Added selection of S-Meter input to Other Menu. Selection is AGC Level
> or RF Signal.
> Default is AGC Level. AGC Level means the S-meter will not go lower than
> the AGC
> Threshold/Knee; RF Signal means that the S-Meter indicates the signal
> strength at the antenna,
> regardless of current AGC threshold or action. Selection is retained
> over power cycles.
>
> 2-S-meter reading is compensated for ATTN setting, Preamp setting,
> signal reduction caused by
> the analog hardware AGC with strong (> S-9+35) signals, and the RF Gain
> control.
>
> 3-S-meter is calibrated so S-9 is 50 uV across 50 Ohms at the antenna
> terminals.
>
> 4-S-meter calibration routine updated to correct for a missing step in
> the table.
>
> 5-S-meter ballistics follow the Hang Time and Decay Rate of currently
> selected AGC profile.
>
> Other changes:
>
> 6-Forced NOTCH to always be OFF after a power cycle.This fixed the
> problem with the DSPs crashing if both NB and NOTCH were enabled during
> a power cycle.
>
> 7-Fixed Serial Command *BS+1
>
> If you get the update and install it, there will be a file named
> 566History.pdf which contains the changes for all versions.
>
> 73..
>
> Howard, WA9AXQ
>
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> ------------------------------
>
> End of TenTec Digest, Vol 199, Issue 18
> ***************************************
>
--
73 - Petr, OK1RP
--
B: http://goo.gl/Fd2JhJ
MeWe: https://bit.ly/2HGPoDx
MeWe: https://bit.ly/2FmwvDt
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|