STUART! Thanks for the encouragement. I'll keep everyone up to date. My
latest theory is excessive heat does something to the 'swaged' SO-239
antenna connections. So it's sitting out i the open now all day receiving
with me operating into a dummy load now and then. I guess I should do as
someone said and just leave it on at 90 watts for an hour into a dummy
load, that should give some sort of answer. i'm workign up to it!! ha ha
73 thanks for all the input
Mike Rutkaus
K4QET
On Fri, Jun 17, 2016 at 12:00 PM, <tentec-request@contesting.com> wrote:
> Send TenTec mailing list submissions to
> tentec@contesting.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.contesting.com/mailman/listinfo/tentec
> or, via email, send a message with subject or body 'help' to
> tentec-request@contesting.com
>
> You can reach the person managing the list at
> tentec-owner@contesting.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of TenTec digest..."
>
>
> Today's Topics:
>
> 1. Re: Omni VII SWR (k8mp@aol.com)
> 2. Re: OMNI VII SWR going high--heat releated (Stuart Rohre)
> 3. Re: OMNI VII SWR going high--heat releated (Al Gulseth)
> 4. Re: Omni VII SWR (Greg S)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Thu, 16 Jun 2016 12:06:39 -0400
> From: k8mp@aol.com
> To: tentec@contesting.com
> Subject: Re: [TenTec] Omni VII SWR
> Message-ID: <15559f6de5c-1daf-1727@webprd-m87.mail.aol.com>
> Content-Type: text/plain; charset=utf-8
>
> Hi Mike,
> Take that combo to FD and run 24 hours of CW in 90 degree weather. That'll
> tell you if you nailed it. :)
> Good luck with it.
> Joe, K8MP
>
> Sent from AOL Mobile Mail
>
>
> -----Original Message-----
> From: Michael Rutkaus <mrutkaus@gmail.com>
> To: tentec <tentec@contesting.com>
> Sent: Thu, Jun 16, 2016 11:49 AM
> Subject: [TenTec] Omni VII SWR
>
>
>
> hmmm. The Alinco DM-340MV analog 12 power suppy might have been bumped up
> to
> slightly over 14v on its adjustment knob. i've lowered that to 12v and kept
> a small fan blowing over the unit and it seems ok right now after a 2 hr
> test. Makes sense. At this point don't know if it needs the extra fan
> blowing from the back or the lowered input voltage, or both.
>
> Kinda stupid, I know.
>
> Mike
> K4QET
>
>
> ---
> This email has been checked for viruses by Avast antivirus software.
> <a href="https://www.avast.com/antivirus"; target="_blank">
> https://www.avast.com/antivirus</a>
>
> _______________________________________________
> TenTec mailing list
> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
> target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>
>
> ------------------------------
>
> Message: 2
> Date: Thu, 16 Jun 2016 14:55:36 -0500
> From: Stuart Rohre <rohre@arlut.utexas.edu>
> To: tentec@contesting.com
> Subject: Re: [TenTec] OMNI VII SWR going high--heat releated
> Message-ID: <57630438.5000500@arlut.utexas.edu>
> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>
> Can you set the rig on top of the bookcase and try its heating up there?
> Sounds like 2.5 inch clearance is NOT enough.
>
> Stuart
> K5KVH
>
>
> ------------------------------
>
> Message: 3
> Date: Thu, 16 Jun 2016 20:14:22 -0500
> From: Al Gulseth <wb5jnc@centurytel.net>
> To: tentec@contesting.com
> Subject: Re: [TenTec] OMNI VII SWR going high--heat releated
> Message-ID: <201606162014.22728.wb5jnc@centurytel.net>
> Content-Type: text/plain; charset="iso-8859-1"
>
> I'm inclined to agree with Stuart - in my book it's not a good idea to put
> a
> piece of equipment in a "claustrophobic" (if you get my drift) enclosure
> without LOTS of forced air flow unless the manufacturer has specifically
> designed the device to withstand that sort of environment.
>
> 73, Al
>
> On Thu June 16 2016 2:55:36 pm Stuart Rohre73, wrote:
> > Can you set the rig on top of the bookcase and try its heating up there?
> > Sounds like 2.5 inch clearance is NOT enough.
> >
> > Stuart
> > K5KVH
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
>
> ------------------------------
>
> Message: 4
> Date: Fri, 17 Jun 2016 14:43:55 +0000 (UTC)
> From: Greg S <oldlongbeard@yahoo.com>
> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> Subject: Re: [TenTec] Omni VII SWR
> Message-ID:
> <5954886.5268190.1466174635674.JavaMail.yahoo@mail.yahoo.com>
> Content-Type: text/plain; charset=UTF-8
>
> Mike- I should think a slightly higher voltage as you listed would be
> fine, as current drops with a rise in supply VDC. It is well within specs.
> I would be sure no ancillary equipment (Other than Mic and/or key and dummy
> load) are plugged in, and see if the situation changes. I would also
> measure that supply voltage with a meter (Scope to look for excessive
> ripple would be better) at the rig. (In-line fuses/fuse holders have been
> known to cause these type of erratics lately on other equipment..... be
> sure to eliminate them as a cause.) If problem persists with rig in free
> air, I am out of ideas for now. Please report back to the list as you have
> time.
>
> 73-
> Greg, KC8HXO
> --------------------------------------------
> On Thu, 6/16/16, Michael Rutkaus <mrutkaus@gmail.com> wrote:
>
> Subject: [TenTec] Omni VII SWR
> To: tentec@contesting.com
> Date: Thursday, June 16, 2016, 11:47 AM
>
>
> hmmm. The Alinco DM-340MV analog 12 power suppy might have
> been bumped up to
> slightly over 14v on its adjustment knob. i've lowered that
> to 12v and kept
> a small fan blowing over the unit and it seems ok right now
> after a 2 hr
> test. Makes sense. At this point don't know if it needs the
> extra fan
> blowing from the back or the lowered input voltage, or
> both.
>
> Kinda stupid, I know.
>
> Mike
> K4QET
>
>
> ---
> This email has been checked for viruses by Avast antivirus
> software.
> https://www.avast.com/antivirus
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> ------------------------------
>
> End of TenTec Digest, Vol 162, Issue 21
> ***************************************
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|