Louis 10 meters IS dead. So dead that I thought my Jupe was busted. A quick
check with my signal generator indicated that all was well. Pleas beg borrow
or steal a signal generator before you try more extreme measures. If there
is really a propblem it will become quite obvious
Mike Tannenbaum k2bn@cox.net
----- Original Message -----
From: "Louis Ciotti" <lciotti@twcny.rr.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, October 29, 2007 6:54 PM
Subject: Re: [TenTec] Triton IV deaf on 10m
>I have not had a chace to pick up of contact cleaner, but I really figured
> TenTec would have gone through the rig and do that sort of basic
> troubleshooting... but I will go ahead and clean them. Hopefully tomorrow
> I
> will get a chance to pick up the cleaner. I will let you know if that
> works.
>
> AS far as 10m being deaf, I am 99% certain the crystals are installed. I
> rember seeing them installed when I had the bottom of the rig apart. Also
> have heard a very faint transmission last week around 28.450, but it was
> almost in the noise. Maybe it's just a bad antenna for the band....
> ----- Original Message -----
> From: "Clark Savage Turner" <csturner@kcbx.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Monday, October 29, 2007 10:00 AM
> Subject: Re: [TenTec] Triton IV deaf on 10m
>
>
>> First, I'd check that you have the crystals for 10 meters in there. I
>> don't think they came standard. If they're there, pull them, spray a
>> tiny bit of DeOxit or something onto the contacts, and reinsert them.
>> Then jiggle the bandswitch around to see if you start to hear the band
>> noise come up. If that doesn't work, write back again.
>>
>> The intermittent transmit can be a lot of things, but the bandswitch,
>> on this rig, would be my first concern. I believe Ten Tec used Caig
>> DeOxit or ProGold on the bandswitch contacts. These little guys can be
>> troublesome, but with care you can put it back into service. Get a
>> little ProGold onto all the bandswitch contacts (carefully, just a bit,
>> wipe off excess on the outside). Jiggle things, make sure all is
>> aligned, check the shaft for wear and the guides to see that they move
>> freely. See how that goes.
>>
>> Clark
>> WA3JPG
>>
>> On Oct 29, 2007, at 1:23 PM, Louis Ciotti wrote:
>>
>>> So amungst other things my Triton IV seems to be stone deaf on 10m.
>>> Another local ham said 10 was open on Sunday and made over 80
>>> contacts... I heard nothing at all... Any ideas??
>>>
>>> As a side note, I am still experiencig intermitant transmit problems.
>>> I have reseated all of the top boards.... Now I will do the same on
>>> the bottom boards. Maybe I will get lucky...
>>>
>>
>> Clark Savage Turner, J.D., Ph.D.
>> Professor of Computer Science
>> Cal Poly State University
>> San Luis Obispo, CA. 93407
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>> --
>> No virus found in this incoming message.
>> Checked by AVG Free Edition.
>> Version: 7.5.503 / Virus Database: 269.15.12/1097 - Release Date:
>> 10/28/2007 1:58 PM
>>
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|