I carefully set the 9420 internal regulators to 14.00v with a digital
meter. TT say to set them all exactly at 14v, within 0.1 volt. I
reckon the actual voltage in my Herc II under full load is not more
than 13.5; I have no easy way to access the inside of the 9420 or the
inside of the Herc II when they are in my very small shack. But it
looks as if I lose around half a volt in the standard 9420 power cable
and connectors, even though I have a separate 120 amp earth bus from the
9420 to the Herc II (and to everything else). The earth bus uses brazed
battery lugs and bolted connections, no crimped joints or plugs/sockets.
I forgot to mention that when I re-soldered the Herc II control board I
also cleaned the relay contacts up. All of the current to the final
transistors goes through them and it does not take much resistance at 20
amps to cause a voltage drop. This is one of the less attractive
features of a low voltage, high current PA, but I still love the thing.
Its so quiet; no 100 cu.ft/minute blower screaming its head off. (If
the airflow is not high enough to lift the 8877 out of its socket, you
simply don't have a big enough blower).
John G3JAG
On 01-Jan-00 Duane Budd wrote:
>
> What does your 9420 output voltage measure under full 600-watt
> r.f. out from the Herc?
>
> 73,
>
> Budd, W5BEN
> w5ben@arrl.net
> Johnson City, in northeast TN
>
> -----Original Message-----
> From: owner-tentec@contesting.com
> [mailto:owner-tentec@contesting.com]On
> Behalf Of Greg Hodsdon
> Sent: Friday, December 31, 1999 5:40 PM
> To: Jim Reid
> Cc: tentec@contesting.com; M. Clark
> Subject: Re: [TenTec] Hercules II Power Source
>
>
>
> Jim:
> Just checked my 10 year old Hercules II/9420 PS on 7.025 into a
> dummy
> load using a VFD wattmeter: 26w in/ 540w out, 35w in/ 600w out,
> and will
> put out well over 600w (with the red LED on!). Keep in mind the
> 9420
> puts out 14.0 vdc, no load.
> Have a good new year!
> 73 de Greg, K7KJ
> Portland, OR
>
>
> --
> FAQ on WWW: http://www.contesting.com/tentecfaq.htm
> Submissions: tentec@contesting.com
> Administrative requests: tentec-REQUEST@contesting.com
> Problems: owner-tentec@contesting.com
> Search:
> http://www.contesting.com/km9p/search.htm
>
>
> --
> FAQ on WWW: http://www.contesting.com/tentecfaq.htm
> Submissions: tentec@contesting.com
> Administrative requests: tentec-REQUEST@contesting.com
> Problems: owner-tentec@contesting.com
> Search: http://www.contesting.com/km9p/search.htm
----------------------------------
E-Mail: John - G3JAG <patents@dx0man.prestel.co.uk>
To: <tentec@contesting.com>
Date: 01-Jan-00
Time: 13:37:16
This message was sent by XFMail
----------------------------------
--
FAQ on WWW: http://www.contesting.com/tentecfaq.htm
Submissions: tentec@contesting.com
Administrative requests: tentec-REQUEST@contesting.com
Problems: owner-tentec@contesting.com
Search: http://www.contesting.com/km9p/search.htm
|