Carl,
I have the RF Parts RFC-3. I heard about using an Ameritron choke too, so they
are really the same choke then.
I was going to drill a new mounting hole and locate the new RFC in a spot with
more clearance around it.
Sounds like a slice of teflon between it and the blower would be much easier.
Rich is going to like reading about tweaking the coil spacing, sounds like just
what he needs now.
Thanks for the info Carl. I have had this project on the back burner for some
time.
73,
Bob
K6UJ
On Apr 5, 2015, at 5:49 PM, Carl <km1h@jeremy.qozzy.com> wrote:
> Ive done several of those conversions using the Ameritron choke which is sold
> to/by RFP as their RFC-3, its $5 less in the MFJ catalog.
>
> I use a piece of hard Teflon wedged in as a spacer from the blower which may
> or may not be needed if using 3CPX800 tubes and more HV; I wasnt going to
> take a chance.
>
> As far as 10-15M tuning I do the armstrong method (only needed less than half
> the time) and open up the coil spacing a bit in the front. It doesnt take
> much spreading to reduce the L a bit and allow the Tune cap to go thru a
> complete peak. Looks neater than moving taps IMO.
>
> I use a 76PA ( got it as a basket case as payment for fixing a Titan) at the
> second station and havent had a reason to do the conversion yet. The three
> 8874's from an upgraded to SS UHF government site will easily do 1800W with
> 100W drive and since I run low drive and 1200W out they should last beyond my
> expiration date (-;
>
> Carl
> KM1H
>
> ----- Original Message ----- From: "Robert Harmon" <k6uj@pacbell.net>
> To: <amps@contesting.com>
> Sent: Sunday, April 05, 2015 4:47 PM
> Subject: Re: [Amps] Alpha 76A 3cpx800 Conversion Tuning?
>
>
> Hi Rich,
>
> I am in a similar quandary.
>
> I upgraded my 76CA to two 3CPX800’s along with the Peter Dahl transformer
> also. I didn’t change the
> existing RFC though. It tunes up beautifully on all bands (except 12) (more
> on that later) More power out
> on all bands. While I was at it I put in new power supply caps and
> equalizing resistors.
> I know the 76’s don’t like 12 meters with their existing RFC and I purchased
> the RFC-3 to install later. I read
> that this choke would work fine and provide 12m. However, later on the Eham
> amplifier forum I asked for info
> about using the RFC-3 and read that the RFC-3 is 1” in diameter and would be
> too close for comfort and would
> cause tuning issues. It was suggested to find one that is 3/4” in diameter
> or install the RFC-3 but mount it farther
> away from the tank circuit components than the original Alpha RFC .Also an
> Ameritron RFC is supposed to be
> another alternate. That is where I am now, I need to find out more on this.
> Hopefully we can hear from
> someone that has done this mod successfully.
>
> (I would suggest posting this issue on the eham amplifier forum. The
> amplifier gurus like Carl, KM1H and Lou W1QJ have been repairing
> amps for years and usually jump in to help.)
>
> Anyway, thats my two cents. Please keep me posted on what you discover.
>
>
>
>
> 73,
> Bob
> K6UJ
>
>
>
>
>
>
>
> On Apr 5, 2015, at 12:36 PM, Rich Hallman - N7TR <rich@n7tr.com> wrote:
>
>> After converting an Alpha 76a to 3CPX800's with a new Peter Dahl upgraded
>> Transformer and installing the new upgraded RFC-3 Plate Choke I am seeing a
>> problem with tuning on 15 and 10 meters. All bands except 15 and 10 seem
>> to tune ok. On 15 and 10 meters....The tuning indicator is at 0 and it's
>> the best tuning I can get. For those who have completed a conversion in the
>> past, can you let me know if you have seen this issue before and if so, what
>> was done to fix the problem? I've seen some info on the net from removing
>> stators from the tuning cap to moving the taps on the tank coil.
>>
>> Thanks for any help you can give!
>>
>> Rich
>>
>> Rich N7TR
>> ex KI3V, N3AMK, WB3JOV
>> www.n7tr.com<http://www.n7tr.com>
>> http://www.qrz.com/db/N7TR
>> Telnet: dxc.n7tr.com N7TR DXCluster
>>
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2015.0.5863 / Virus Database: 4321/9461 - Release Date: 04/05/15
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|