>A tetrode can be grounded grid.
>
>Polarization requirements are not the same than dynamic circuit and
>have nothing to do with the amplifier configuration.
>Stated it, and generally speaking, why to bother with a tetrode in a Gg
>and why to be forced in building a second PS.
>Use a triode, instad.
The tuned input circuits for the soon to be 10 amateur bands below 30 MHz
are not a piece of cake for a Q of 2-3, which is needed with solid state
transceivers driving G-G amplifiers. To fully cover the 3.5MHz and the
28MHz bands, two additional tuned inputs are needed. With a grid-driven
amplifier, one roller-coil and one terminating R gives a good match
everywhere.
-- A second power supply is not needed for the 4cx800 (30mA/350V screen)
because the ideal setup is to obtain the screen V from a shunt zener
string powered by the current from a resistor connected to the HV-PS.
The neg. grid bias potential can come from a half-wave rectifier,
C-filter connected to the mains.
>All the matter is a bit obscure, it becomes expecially annoying when
>using tubes where screen current has to be zero or anyway very low.
>
There is normally screen current under signal conditions.
>In my experience I never found a tetrode with more gain than a triode
>when used as a Gg amplifier at full power.
>
Agreed, and there's usually less gain than with a high-Mu triode.
However, a grid-driven 8281 tetrode will do c. 23db gain with 170w drive.
ciao, Mauri
>
>
>
>Grids be dynami
>
>
>
>> Richard wrote:
>> >
>> >
>> >>Greetings,
>> >>
>> >>What's the input impedance for a GG 4CX800A?
>> >>
>> >With a 2w? grid, running it in g-
>g might not be a wonderful idea. The
>> >4cx800 is designed for Class AB1, which means 0 grid current.
>> >
>> With the correct DC voltages applied to the control grid and screen, a
>ny
>> tetrode will work fine with both grids at RF ground. This is very comm
>on
>> at VHF and above, and occasionally seen at HF.
>>
>> According to the way the power supply is wired, you can chassis-
>ground
>> either grid, and RF-bypass the other one; or you can DC-ground the
>> cathode and RF-bypass both grids.
>>
>> As Rich says, what you can *not* do is run a modern tetrode with both
>> grids directly grounded to the chassis. The control grid takes too lar
>ge
>> a share of the combined grid current.
>>
>> Unfortunately - and wrongly -
> this method of operation seems to be what
>> most hams understand as "Grounded Grid". It only works with the old
>> glass tubes because they were primarily designed for Class C, and have
>
>> very hefty control grids that can stand the extra current. But even
>> these tetrodes were never designed to be operated with both grids
>> chassis-grounded - it's a ham invention.
>>
>>
>> --
>> 73 from Ian G3SEK Editor, 'The VHF/UHF DX Book'
>> 'In Practice' columnist for RadCom (RSGB)
>> New e-mail: g3sek@ifwtech.co.uk
>> New website: http://www.ifwtech.co.uk/g3sek
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>_______________________________________________
>Amps mailing list
>Amps@contesting.com
>http://lists.contesting.com/mailman/listinfo/amps
>
- R. L. Measures, a.k.a. Rich..., 805.386.3734,AG6K,
www.vcnet.com/measures.
end
|