Search String: Display: Description: Sort:

Results:

References: [ +from:k1ttt@verizon.net: 12 ]

Total 12 documents matching your query.

1. Re: [Yaesu] Yaesu FT767GX Dead (score: 1)
Author: David Robbins <k1ttt@verizon.net>
Date: Mon, 09 Jul 2012 06:43:00 -0500 (CDT)
see if it has a battery backup in it and replace that. try turning it on with the cpu reset buttons pressed. or just wait a while after powering up, i have some ft-1000mp's that seem to take a minute
/archives//html/Yaesu/2012-07/msg00002.html (7,799 bytes)

2. Re: [Yaesu] FT1000MP Does not power up for 4 to 5 minutes (score: 1)
Author: David Robbins <k1ttt@verizon.net>
Date: Mon, 30 Jul 2012 06:58:55 -0500 (CDT)
yes, this is a common problem with mp's, i have a couple that do it occasionally, usually after being turned off for a while. I was wondering if anyone has seen this one? This started about a month a
/archives//html/Yaesu/2012-07/msg00014.html (8,583 bytes)

3. Re: [Yaesu] FT890 strange behavior (score: 1)
Author: David Robbins <k1ttt@verizon.net>
Date: Thu, 11 Jul 2013 06:33:17 -0500 (CDT)
the physical distance between the radio and the supply is not a factor, it is either rf being picked up by the cables to the supply or the radio is overloading it and it is shutting down. now normall
/archives//html/Yaesu/2013-07/msg00003.html (8,306 bytes)

4. Re: [Yaesu] Digital (score: 1)
Author: David Robbins <k1ttt@verizon.net>
Date: Wed, 05 Mar 2014 09:48:37 -0600 (CST)
put radio in usb, start software using computer mic and speakers for in/out, receive using computer mic, transmit by holding mic near computer speaker and pushing ptt. not the easiest, but gets you o
/archives//html/Yaesu/2014-03/msg00004.html (7,190 bytes)

5. Re: [Yaesu] FT1000MP and PSK31 (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Sun, 19 Mar 2017 10:53:54 +0000
In my setup I route the computer audio to both the mic jack and the packet jack. For doing rtty i use pkt-lsb which gets the audio from the rear packet jack and also allows use of the narrow cw filte
/archives//html/Yaesu/2017-03/msg00014.html (9,109 bytes)

6. [Yaesu] ft-1000mp mod? (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Mon, 10 Jul 2017 10:26:27 -0500
Has anyone seen or done a modification to the ft-1000mp to enable using whatever antenna is being used on receive to be shared for use by an sdr for a waterfall display?? ____________________________
/archives//html/Yaesu/2017-07/msg00004.html (6,903 bytes)

7. Re: [Yaesu] ft-1000mp mod? (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Tue, 11 Jul 2017 09:00:45 -0500
Hmmm, simple option, no board modifications, easy access, no measurable change to rx I can see... after going through the rf board bandpass filters the rx rf is split to go to the first mixer to get
/archives//html/Yaesu/2017-07/msg00006.html (9,248 bytes)

8. Re: [Yaesu] ft-1000mp mod? (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Tue, 11 Jul 2017 10:21:43 -0500
As I pointed out, this tap location is not the same as the rx out to rx in loop you describe in that it doesn't need an external switch and it takes advantage of the mp's pre 1st stage rf amp bandpas
/archives//html/Yaesu/2017-07/msg00008.html (13,284 bytes)

9. Re: [Yaesu] FT1000MP overheating and audio failure (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Mon, 28 May 2018 15:15:24 -0500
Was the fan coming on? That could have failed causing runaway overheating of the power supply which would cause it to shutoff, I think there is a thermal switch in there somewhere. could also be bias
/archives//html/Yaesu/2018-05/msg00005.html (10,430 bytes)

10. Re: [Yaesu] FT1000MP original and FT8 setup (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Wed, 12 Sep 2018 08:54:31 -0500
Why not just use usb mode? Works fine here! David Robbins K1TTT e-mail: mailto:k1ttt@arrl.net web: http://wiki.k1ttt.net AR-Cluster node: 145.69MHz or telnet://k1ttt.net:7373 ++++++++++++++++++++++++
/archives//html/Yaesu/2018-09/msg00005.html (10,878 bytes)

11. [Yaesu] ft1000mp RIT encoder (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Sat, 06 Oct 2018 10:36:24 -0500
Got a flakey RIT encoder on an ft1000mp style radio? Here is how to replace it for $1.28 and ½ hour of work. http://wiki.k1ttt.net/2018%20Maintenance%20and%20Upgrade%20Blog.ashx?NoRedir ect=1#mprit D
/archives//html/Yaesu/2018-10/msg00000.html (6,660 bytes)

12. Re: [Yaesu] FT1000MP problem - Does anyone know what it might be? (score: 1)
Author: "David Robbins" <k1ttt@verizon.net>
Date: Mon, 05 Nov 2018 06:49:15 -0500
That sounds like multiple problems because the only thing common to transmit and receive after the power/swr measurement point are the t/r relay and the a/b ant relays... nothing related to band sele
/archives//html/Yaesu/2018-11/msg00002.html (9,833 bytes)

Current List: 1 - 12
Page: [1]
This search system is powered by Namazu