I am looking for a Yaesu FT100D HF/VHF/UHF radio. Need the mic and power cord with it, and would take other accessories if you have them-but they are not needed. I am looking for a late 2001 (1L or l
Given the recent discussion about service opportunities for a FT100 and the lack of parts availablility, what is the consensus of the group? Is a used FT100-updated by Yaesu a few years ago to a D mo
I have a Yaesu FT450 I am looking to sell. Bought it to use while my Icom 706 was going to be repaired, but the repair will cost too much so I will just use it as is. The Yaesu FT450 is a 100 watt HF
I have a Yaesu FT450 I am looking to sell. Bought it to use while my Icom 706 was going to be repaired, but the repair will cost too much so I will just use it as is. The Yaesu FT450 is a 100 watt HF
I am looking for a good condition, good working Yaesu FT450. Don't need the AT model but will take one if it has the tuner installed already Let me know your price shipped to Lawton, OK Zip 73507. 73
I have a Yaesu FT100D HF/6m/2m/70cm radio I am looking to make a trade on. This is the mobile sized rig that does 100 watts on HF and 6m, 50 watts on 2m, and 20 watts on 70cm, CW/SSB/AM/FM. It comes
I have recently come across a couple of stories concerning the Murata Ceramic filter needing to be replaced in the Yaesu FT857 and the FT897. Was this a common failure? Did it occur for most of these
It is fairly easy to run a cable between the mic jack on the FT100 and the line out jack on a computer (turn on the VOX) and run AFSK that way, or is it more complicated. I seem to remember hearing t
I have for sale almost a complete YSK-857 seperation kit. It has the separation cable to remote mount the faceplate, the mobile bracket for the faceplate, and the mobile bracket for the radio-with sc
I have for sale almost a complete YSK-857 seperation kit. It has the separation cable to remote mount the faceplate, two (2) of the the mobile brackets for the faceplate, and the mobile bracket for t
Does anyone know the size of the circuit board screws used in the FT857, and if they are readily available at any hardware store? Mine has a couple that seem to have stripped threads, and would like
I have for sale a Yaesu ATU-450 which is the internal automatic antenna unit for the Yaesu FT450. They sell new for $149.95, I am asking $80 shipped for it and can take paypal, check, MO or Cash. Tra
I have an early model Yaesu FT857 that has now developed the dreaded 6 meter oscillation problem. It had the poor audio on 6m for about 5 weeks after I got it, then it started going into oscillation
I have for sale a Yaesu G-800S medium duty rotor. It is rated at 17 square feet of wind load when mounted in a tower. The rotor is in very good condition, turns fine, and the control box tracks the m
I have for sale the lower mast mounting bracket for the Yaesu rotors. It has the bolts and nuts to tighten it around the mast as well. These sell new for $40 plus shipping. I am asking $28 shipped fo
I have for sale a power cord for the HF rigs that use the 6 pin molex connectors. It is in 2 pieces, connected by Anderson power poles. The side with the connector is about 40 inches long, and is pre
I have for sale a Yaesu GS-232B computer-Yaesu rotor interface. This allows you to do computer control of your Yaesu rotor, so you can use your logging program or radio control program to turn your r
For you Yaesu fans out there I have a genuine Yaesu mouse pad which would look great in the shack. It is round, approximately 8 inches in diameter, and shows their current line of radios, including t
I have for sale the West Mountain Radio rigblaster original model. This is the model that allows you to plug your microphone into the interface, and the interface plugs into your mic jack, and you ca
Is it possible to use the CAT commands with the FT450 and the N1MM logging software to program the function keys to send the voice keyer messages or CW keyer messages for the FT450 while using N1MM?