All; I am a brand new Writelog User. I am trying to implement CT Compatible mode so I can use the F1 key. I have entered the following line under the Configuration Section in my WRITELOG.INI file: Ct
Doug; That did it. Thanks for the quick response. 73, Al, K0AD _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.contesting.com/mailman/listin
All; I am brand new to RTTY. I have WriteLog up and going but seem to have a little trouble easily tuning in RTTY signals. Can someone give me some tips on the best settings on the FT1000D. On LSB, I
Thanks to all of you that responded to my question on using the 500 and 250 hz filters with the FT1000D on RTTy using AFSK. Several of you mention that I should run the SHIFT control at about 9:00 to
Newbie Question. Is there some trick to getting packet via a TNC to work with Writelog? My configuration is Windows 98 wtih COM1 connected to Radio and COM2 connected to TNC. This configuration works
I am trying to implement two band decoders for an SO2R setup with Writelog. My two radios are an FT1000D and an ICOM 746. The FT1000D has four nice BCD lines to drive one of the band decoders. Howeve
I set up a two computer Club Station for networking in SS last weekend. Both stations use Windows 98. I followed the steps under "Networking Operations" in the help file. Specifically, I configured a
All; I solved the Dupe Checking Problem from my 11/22/04 Post. Thanks for all the help from W4MYA, N5NJ, K9JY, and others. K9JY correctly identified my problem: "The key is that one PC 'registers for
I know this has probably been discussed before but I just wanted to see if there is a simple answer. In our Multi-Single SS Operation, we were running two networked stations. If we started to enter a
Before reverting back to TR for Multi-Op contests with Serial Numbers (i.e SS, WPX, etc), I just wondered if anyone could point me to a solution to this problem when using Writelog. I didn't get any
Can anyone point me to a link explaining how to setup WL and MMTTY for SO2R using the right and left Mic Inputs on a sound card. I think I understand the hardware setup but it's not clear to me how t
Is there any secret to using direct FSK keying on the ICOM 746? I built up a couple simple 2N2222 / 1 K resistor interfaces. This seems to work fine when keying my FT1000D. However, when trying to ke
Thanks to N0AT, KV1W, and others concerning my problems with the 746 FSK interface. I did get it going although I am not sure exactly what the problem was. I rebuilt the cable with new parts and it s
In a message dated 1/17/2005 4:36:10 PM Central Standard Time, k1dan@profirefighter.com writes: The Writelog program is all that changes, my rig does not change modes during this time. I am using a K
I can't seem to figure out how to have WL enter the transmitter number in the Cabrillo file for Multi-Two contests such as NAQP. I have two computers networked and all seems to be working well. I see
Does anyone know if there are any SSB Pileup programs out there. I've come across plenty of great CW ones, including Morse Runner, but can't seem to locate anything similar for SSB. Just curious. 73,
All; Is there a way to kick off messages in RTTY with just the mouse. I notice that you can right click and send the F3 and F4 messages. But what about F1 and F2? Essentially, I am wondering if I can
I've noticed that when I hit shift+Fkey to record a voice message that the rig goes into transmitt. I do have comm ptt selected under port setup. However, I would think the rig should not go into tra
I see the dropout also at random times. Several times an hour, at least. I thought it was only me. I'm running WL 10.51 with MTTY Version 1.65 with Windows 98. Comm PTT is set to YES on the Radio (FT
Barry, W2UP, came up with the operator error that I had made - still had single operator checked from a previous contest. 73, Mike, K4GMH Mike; What - exactly did you have to do to get the spots work