There have been periodic reports of incompatibility between some paddles and WinKey. This appears to be due to the use of "new" contact materials designed to reduce oxidation issues. Some of these ma
Except the bug exists in the HARDWARE drivers from FTDI, Prolific and nearly every other USB chipset manufacturer... that driver becomes part of the operating system. It is not within the control of
An update to microHAM Router (Router 3.1.0) is available for download at: http://www.microham.com/Downloads/urouter_release_03_01_00.exe Key changes to this version: - Enhanced support (frequency/mod
The Piexx (UX-14px) can be set for either 1200 or 9600 baud on the CI-V (1/8" jack) port. The RS-232 port can be set for 4800 or 9600 baud. The US-14px uses 8 bit, no parity, one stop bit. Under som
Nick, The microKEYER and DXD Doubler presently work fine for SO2R operation. I have a pdf showing the hook-up information. Those who might need it can e-mail me directly. microHAM will be introducing
John, I doubt that you will be able to use the parallel port of the VDS-1003 for CW. Note the "features" "One parallel printer port with DB-25 Pin female connector (port can only be used with a print
I have uploaded a PDF of the information on MK2R and MK2R+ to the files section of the microHAM group on Yahoo. The file is a basic "features" listing of the new SO2R controllers. The same informatio
The Peter I team had around a dozen of the microHAM microKEYER interfaces ($259) and not any of the "$99" boxes as far as I know. Some of the Peter I operators took their own radios (IC-7000/IC-706)
Jim, USB Interface II will support FSK when used with MMTTY and EXTFSK (using the DTR line). However, last I checked the software FSK in Writelog was "fixed" on the TxD line which is unavailable (use
Ed, As I responded to Froggy on the microHAM support e-mail: This not a "fault" of any software or hardware ... simply a lack of a common interface. The potential solutions are: 1) the ability of Wri
Jim, Who is blaming Writelog? Since when should microHAM be responsible to add features not provided by a program's author (in this case the author of the MMTTY plug-in for Writelog)? microHAM suppor
For two reasons: 1) the FSK output is available when MMTTY is used with EXTFSK in the following situations that I know of: MMTTY stand-alone, MMTTY with Logger32, DX4Win, DXLab/WinWarbler, N1MM Logg
Froggy, Quite simply, although I do a lot of customer support internationally, microHAM America is an independent distributor, not a division of microHAM, s.r.o (the manufacturer). This arrangement i
Joe, The DigiKeyer does not include a WinKey keyer ... it supports only the Generates" method of CW generation. As such, it is susceptible to the typical operating system and USB delays with "PC Gene
Duane, Look at the Writelog help file under "CW, and RTTY and Voice Memory setup:" ^ dot-length space (also called half space, but its a dot-length) The caret is upper case 6 on U.S. keyboards. With
With MMTTY the most common cause of the "overflow" indication is excess audio signal level to the sound card. If you are using a laptop and feeding it from the speaker or headphone output of a radio,
Barry, Many of the low end Audigy sound cards have only a single input shared between mic and Line. If you go back to the Audigy, make sure it is set for LINE ... otherwise you will overdrive the mic
WriteLog AFSK and microHAM DigiKeyer work fine as long as you select the proper "sound card" (USB Audio Codec). WriteLog FSK will not work with any microHAM product ... you must use the MMTTY plug-in
Rich, The current HP laptops with "Conexant AMC Audio" will echo the mic to the headphone/speaker output. The Soundboard test program gives them a score of 6b. However, the report indicated that the