- 1. [TowerTalk] Stripping LMR-600 (score: 1)
- Author: "Tommy Alderman" <aldermant@windstream.net>
- Date: Wed, 21 Apr 2010 06:56:45 -0400
- What is the recommended tool for stripping LMR-600 for a type-N connector? Do most of you use just a sharp blade and careful measurements or do you recommend the purchase of a stripping tool? If you
- /archives//html/Towertalk/2010-04/msg00605.html (7,395 bytes)
- 2. Re: [TowerTalk] Stripping LMR-600 (score: 1)
- Author: Scott Reed <sreed@nwwnet.net>
- Date: Wed, 21 Apr 2010 08:08:28 -0400
- I use the LMR600 strip tool from Tessco. -- Scott Reed Owner NewWays Networking, LLC Wireless Networking Network Design, Installation and Administration Mikrotik Advanced Certified www.nwwnet.net (76
- /archives//html/Towertalk/2010-04/msg00612.html (8,506 bytes)
- 3. Re: [TowerTalk] Stripping LMR-600 (score: 1)
- Author: "Roger (K8RI)" <K8RI-on-TowerTalk@tm.net>
- Date: Wed, 21 Apr 2010 08:38:23 -0400
- I purchased one through Davis (Orion Wire). Works just fine. 73 Roger (K8RI) _______________________________________________ _______________________________________________ TowerTalk mailing list Tow
- /archives//html/Towertalk/2010-04/msg00613.html (8,236 bytes)
- 4. Re: [TowerTalk] Stripping LMR-600 (score: 1)
- Author: "Tommy Alderman" <aldermant@windstream.net>
- Date: Wed, 21 Apr 2010 13:28:43 -0400
- Thanks Roger. Can you also cut the braid shield and the dielectric with that stripping tool? Thanks again. 73, Tom - W4BQF can I purchased one through Davis (Orion Wire). Works just fine. 73 Roger (K
- /archives//html/Towertalk/2010-04/msg00628.html (9,435 bytes)
- 5. Re: [TowerTalk] Stripping LMR-600 (score: 1)
- Author: "W0MU Mike Fatchett" <w0mu@w0mu.com>
- Date: Wed, 21 Apr 2010 11:58:38 -0600
- I use a stripping tool. They are great! CC Packet Cluster W0MU-1 W0MU.NET or 67.40.148.194 "A slip of the foot you may soon recover, but a slip of the tongue you may never get over." Ben Franklin Wha
- /archives//html/Towertalk/2010-04/msg00630.html (8,832 bytes)
- 6. Re: [TowerTalk] Stripping LMR-600 (score: 1)
- Author: "Roger (K8RI)" <K8RI-on-TowerTalk@tm.net>
- Date: Thu, 22 Apr 2010 04:15:39 -0400
- Yes, it's one of the "twist" type. You stick one end over the end of the coax and make a couple of twists, then turn around and use the other end. That leaves the coax ready for the connector. It's e
- /archives//html/Towertalk/2010-04/msg00658.html (11,173 bytes)
- 7. Re: [TowerTalk] Stripping LMR-600 (score: 1)
- Author: "Gary E. Jones" <garyejones@cmaaccess.com>
- Date: Thu, 22 Apr 2010 07:16:21 -0500
- Check with Davis RF and/or Texas Towers for a stripping tool I use a stripping tool. They are great! CC Packet Cluster W0MU-1 W0MU.NET or 67.40.148.194 "A slip of the foot you may soon recover, but a
- /archives//html/Towertalk/2010-04/msg00663.html (9,653 bytes)
This search system is powered by
Namazu