Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Ham\s+rotor\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Ham\s+rotor\s*$/: 7 ]

Total 7 documents matching your query.

1. [TowerTalk] Ham rotor (score: 1): Author: shane@icu2.net (Shane Autrey); Date: Wed, 8 Apr 1998 02:49:07 +0100; I am using a Ham M rotor with a Ham II rotor control box. I have the original box for the Ham M itself and it works just fine. I was wondering how i could get the direction indicator on the Ham II co; /archives//html/Towertalk/1998-04/msg00190.html (7,848 bytes)
2. [TowerTalk] Ham rotor (score: 1): Author: shane@icu2.net (Shane Autrey NC4SA); Date: Wed, 8 Apr 1998 05:59:15 +0100; Now that i have the wiring diagram for the rotor what do i need to do so that the control box itself will recognise the direction the motor is pointing in. The Ham M control box reads the direction c; /archives//html/Towertalk/1998-04/msg00194.html (8,753 bytes)
3. [TowerTalk] Ham rotor (score: 1): Author: grimm@lynchburg.net (Kenneth D. Grimm); Date: Wed, 08 Apr 1998 07:32:03 -0400; Shane, Dick has given you the correct hookup for both the Ham M and the Ham II. It is definitely time to get out your VOM and do a little checking inside the box and with your connecting wires. The r; /archives//html/Towertalk/1998-04/msg00198.html (10,453 bytes)
4. [TowerTalk] Ham rotor (score: 1): Author: grimm@lynchburg.net (Kenneth D. Grimm); Date: Wed, 08 Apr 1998 07:45:20 -0400; Sorry about that last post. After re-reading you message, I see that you do have the diagram . Take the HAM II box apart and start checking with the VOM is still my best suggestion and the place I wo; /archives//html/Towertalk/1998-04/msg00200.html (8,009 bytes)
5. [TowerTalk] Ham rotor (score: 1): Author: k1vr@juno.com (Fred Hopengarten); Date: Wed, 08 Apr 1998 10:40:20 EDT; On Wed, 8 Apr 1998 05:59:15 +0100 "Shane Autrey NC4SA" <shane@icu2.net> writes: to K1VR: Sound as if you have the calibrate switch ON. Try to push a button in or throw a switch. Or perhaps the calibr; /archives//html/Towertalk/1998-04/msg00210.html (8,289 bytes)
6. [TowerTalk] Ham rotor (score: 1): Author: KJ6Y@aol.com (KJ6Y); Date: Wed, 8 Apr 1998 12:18:26 EDT; The wiring on the two rotors is the same. If your indicator is all the way to the right, it indicates your in the calibrate position. Push in the calibrate button. It is usually a push-push type swit; /archives//html/Towertalk/1998-04/msg00217.html (7,511 bytes)
7. [TowerTalk] Ham rotor (score: 1): Author: shane@icu2.net (Shane Autrey NC4SA); Date: Wed, 8 Apr 1998 17:08:56 +0100; Guys based on your responses to my post my problem has been solved. The calibration pot was bad in the control box and when i replaced it the meter and everything else worked correctly. I thank you a; /archives//html/Towertalk/1998-04/msg00221.html (7,469 bytes)

Current List: 1 - 7
Page: [1]