- 1. [TowerTalk] HAM IV Height (score: 1)
- Author: "James Setzler" <jms_k1sd@verizon.net>
- Date: Thu, 19 Sep 2013 11:35:16 -0400
- Greetings, I'm replacing a HAM IV with a Yaesu G-800GXA and concerned about the depth of the mast into the rotor housing. What is the dimension on the HAM IV from the mounting plate to the point that
- /archives//html/Towertalk/2013-09/msg00251.html (6,575 bytes)
- 2. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: iain macdonnell - N6ML <ar@dseven.org>
- Date: Thu, 19 Sep 2013 09:00:32 -0700
- about 8.5" 73, ~iain / N6ML _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://lists.contesting.com
- /archives//html/Towertalk/2013-09/msg00252.html (7,060 bytes)
- 3. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: "Larry" <lknain@nc.rr.com>
- Date: Thu, 19 Sep 2013 12:57:13 -0400
- 8.5 inches. Although, I have always had to shim it up a bit (maybe 0.25 inch) with washers at the mounting screws to keep the terminal strip off the shelf. 73, Larry W6NWS Greetings, I'm replacing a
- /archives//html/Towertalk/2013-09/msg00253.html (7,779 bytes)
- 4. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: "Roger (K8RI) on TT" <K8RI-on-TowerTalk@tm.net>
- Date: Thu, 19 Sep 2013 14:30:52 -0400
- When the terminal strip fails, I replace them withe the pigtail and connectors used in the tailtwister. 73, Roger (K8R) _______________________________________________ _______________________________
- /archives//html/Towertalk/2013-09/msg00254.html (7,314 bytes)
- 5. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: k6ye@q.com
- Date: Fri, 20 Sep 2013 00:44:49 -0400 (EDT)
- Jim, I replaced a T2X Tailtwister with a Yaesu G-2800DXA and other than rewiring the plug on each end, I had to change nothing at all. The fit was perfect. I do use a thrust bearing to carry all of t
- /archives//html/Towertalk/2013-09/msg00256.html (8,018 bytes)
- 6. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: "Roger (K8RI) on TT" <K8RI-on-TowerTalk@tm.net>
- Date: Fri, 20 Sep 2013 03:03:04 -0400
- I replaced a T2X Tailtwister with a Yaesu G-2800DXA and other than rewiring the plug on each end, I had to change nothing at all. The fit was perfect. I do use a thrust bearing to carry all of thee w
- /archives//html/Towertalk/2013-09/msg00257.html (8,848 bytes)
- 7. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: Grant Saviers <grants2@pacbell.net>
- Date: Fri, 20 Sep 2013 08:03:35 -0700
- Roger, I have both 2800s Yasesu & Orion. Both are excellent rotators, but with large differences in capabilities and that shows in the price. However, if you ever need to dig into the yaesu controlle
- /archives//html/Towertalk/2013-09/msg00259.html (11,363 bytes)
- 8. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: "Roger (K8RI) on TT" <K8RI-on-TowerTalk@tm.net>
- Date: Fri, 20 Sep 2013 12:22:37 -0400
- I have both 2800s Yasesu & Orion. Both are excellent rotators, but with large differences in capabilities and that shows in the price. However, if you ever need to dig into the yaesu controller, your
- /archives//html/Towertalk/2013-09/msg00261.html (9,838 bytes)
- 9. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: "James Setzler" <jms_k1sd@verizon.net>
- Date: Fri, 20 Sep 2013 13:23:42 -0400
- Gentlemen, Thanks for the replies. I just came down from the tower and the swap went off without a hitch. An easy remove/replace. 73 James K1SD From: James Setzler [mailto:jms_k1sd@verizon.net] Sent:
- /archives//html/Towertalk/2013-09/msg00262.html (8,151 bytes)
- 10. Re: [TowerTalk] HAM IV Height (score: 1)
- Author: Steve Dyer <w1srd@yahoo.com>
- Date: Sat, 21 Sep 2013 08:57:41 -0700
- I just put the Orion in my LM-470 and it fits perfectly. I wish the 2800DXA fit as well in my WT-51. I had to bend the rods out to clear the protruding "knobs" on upper rotating bell and now cannot f
- /archives//html/Towertalk/2013-09/msg00264.html (11,289 bytes)
This search system is powered by
Namazu