TTers I too ka lightning hit and my Ameritron RSV 5 the older straight line SO-239 design The are the DPDT open frame type relays The only visible info is on the coil top 12VDC 99K RSC0 Wayne ,W3EA S
Mike, The Yaesu family of rotators also the kenpro and Create have ta similar cast mast mounting clamps. There failure is improper instaltion either over tourquing or misalingement between the mast b
Bill, According to the Rohn Bible Rohn -55 it uses 6 pieces 5/8 X 3 ¼ NC bolts Wayne W3EA, Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10 I recently picked up a couple
Mike, I echo Keiths assement. Mr. Andersons instructions are vague in some areas . Having installed quite a few three tings are paramount. The three piece tower brackets must be 100% LEVEL both aroun
Fred, Not sure of your applications for these BUT IMHO I dont think its an appropriate anchor for tower installation . All guys tower manufacture have speck for there hight/windload/anchor specificat
Wild guess here, Lower your Tower Crank up and just lower in hights? Or lay over and upside down ? No guess if you just lowered, BUT if it was on its side H20 and enter a rotor . Help a fellow ham wi
Bob, The hi Gain/Telex now MFJ is a reliable rotor its flaws are well documented ( stuck wedge brake full travel ) and the slip off BRAKE botton while turning at full speed and load. There a a number
Bob, Not sure not a chemist I looked at the product and IMO the product has no expiration date. On this subject I responded a few times and there are two camps ( go figure) As I use when I was employ
Bob, Also the winches were not covered. Left in the open, I would do my yearly maintenance and use rifle bore rage sprayed with the S00201 on the 3 ft. of open cable from the winch drum to the droppe
Tom, What Size CATV line ? Wayne , Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10 Any new/old information out there on building CATV Hardline Connectors. In the past I
Phil, I do the electrical tape and use either in the field a 36 in long BOLT cutter or in the shop a high speed Wizzer ( cut off tool ) Wayne ,W3EA Sent from Mail<https://go.microsoft.com/fwlink/?Lin
Bill, The Hi Tower base is a hinged T and it mounts to the EARTH with three 1 ¼ od tubes that affix to the three insulators. IMO you need to rent a CORE drill to drill into your exsiting base and EPO
Ron, As stated B-4 the F-12 orginial small dia. Balun can be problematic over time H2O either at the wire exit or at the SO barrel end . Balun Design are the Balun of choise IMO Wayne , Sent from Mai
Rohan use to or maybe still dose. Manufacture a steel grid Thayer put cement blocks on and had a small mast ( for tv antenna only ). You can fab one out of wood would be weird looking with sandbags o
Acording to PLP bible. For 3/16 EHS min Dia. Is 1 and Max Dia. Is 1 ¾ ¼ EHS min Dia. 1 1/8 and max is 1 ¾ Wayne , W3EA Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10 It
Good Advice Gene, With my first climing belt Klein Linesman , There are a few rings and loops that is possible to clip to. And I used Dual tool pouches do site line was obscured it was look tug feel
Never had the optunity to meet Roy, But I spent time on his web site His ingnunity was outstanding His fbracated tower amazing.. he had to trust his design as he climbed it ! His 4 sq on the AZ deser
Al. The push pull switch is for calibration the full scale meter to your IR on your specific cable run. You push it in call switch button and turn it to adjust meter full scale Wayne W3EA Sent from m
John, Having used Phillystran I had either 3/16 , ¼ or 5/16 EHS cable terminated to the ground anchor/turnbuckle I use a LOOSE gauge This is not as accurate as a dynamo meter. BUT IMO for amature app
Drew, Tried to stay away from this thread, but you point if splceing @ HF jolted my reaction. My Mentor and I know friend of yours Gerry Mathis W3GM was the king of wire nuts. The all plastic ones. H