I have the W0MLY RX1 Manual. I would be happy to copy it for you. It is two pages long. The two RX1's I have in service work very well. Send me your mailing address. 73, Tim K3LR http://www.k3lr.com
Clive: I am using .01 uF discs across the brushes and .1 uF large AC rated bypass (to the tower ground) capacitors on each of the motor leads within 6 inches of the motor. I have no hash as a result
I have installed them both ways. 1032 and 1022. Either one can be installed solo. It just takes longer... I have 13 of them up and running! 73, Tim K3LR http://www.k3lr.com List Sponsor: Are you thin
Two big grip preforms along with one in-line guy wire insulator of suitable strength sure make a very strong and reliable (safe) in-line splice. I seem to recall seeing a special back to back preform
ANTENNA TECHNOLOGY Room #1 2:15 PM to 5 PM Friday May 18, 2001 Tim Duffy , K3LR Moderator "What's Really Inside the Trap in Your Antenna" Tom Rauch, W8JI "The Big Bertha Rotating Monopole for Monoban
We are less than a month away from the big Dayton Contest Dinner event. There is only about 2 weeks left to get tickets sent to you in time for Dayton. Do not delay your ticket request. We expect a c
The North Coast Contesters are pleased to announce: The 9th Annual Dayton Contest Dinner Tickets go on sale MONDAY, March 19, 2001. Sponsored by CQ Magazine Master of Ceremonies is CQ Magazine Contes
I have a 4 square on 10 meters with the Comtek hybrid and it works perfect. I am using 4 ground mounted 1/4 wave verticals with 20 radials under each. I have no power in the dump load at 28.3 and a 1
The coupler will not work correctly with 110 ohm radiators on the ends of odd quarter wave 75 ohm multiples. It is meant to work with close to 50 ohm antennas (preferably 1/4 wave verticals) at the e
I have used 4 square vertical arrays on many bands to augment our multi receiving station capabilities. As reported by other stations, the polarization isolation and small size lends itself very well
The contact is the Radio BookStore. They will have tickets starting March 15. 73, Tim K3LR -- FAQ on WWW: http://www.contesting.com/FAQ/towertalk Submissions: towertalk@contesting.com Administrative
If CushCraft were to discontinue their Amateur antenna line and the support for it, it would make getting parts for existing CushCraft antennas impossible. I don't think that would be the best situat
Hi Nat! There IS quite a distance difference between W3LPL and K3LR, with LPL being much closer to Europe than LR. LR enjoys a distance advantage to Japan over LPL. As K8DX pointed out, the 4 element
The problem is not noise caused by the motor. The noise filter at the motor does a good job, except when the capacitors blow (which has only happened on my 10 meter tower). N3RS verified that there i
Hi Ty! Thanks for your ideas. I am committed to finding the problem. I have tried all of the bonding ideas you mentioned. I think N3RS has tried all of them as well. I have disconnected the control w
This is what will be presented at the Dayton Antenna Forum this year. I hope to see you there! I am not sure what the Room number is for the forum. It should be in the same place that it has been for
Do you, or someone you know, have at least 16 Dorman 1 1/8" plated U-bolts that they would sell to me? I have a side mount that is drilled for this specific U-Bolt and my local distributor is out of
Pictures of the 3 element 80 meter M2 antenna take down project last weekend at K3LR can be viewed at K8CX's Ham Gallery site: http://www.paradox2010.com/ham/gallery.htm They are located in the K3LR
On Friday, May 15th in Room 1 HARA (old Room 5, same room as past years). ANTENNA TECHNOLOGY Moderator: Tim Duffy K3LR "Low Band Receiving Antennas for Limited Space" Gary Breed, K9AY "Comparing Trib