Looking for a copy of the m2 40m4lldd? If you have a scanned or digital copy please forward to my email. Lost mine somewhere in the shipping and hadn't heard back from M2 yet. Thanks... Rich N7TR ex
Looked in the archives and see a bunch of questions for the same info but not many answers. Looking for the wire diagram for the UP / Down Control and limit switches for an HDX589. This is for the no
Looking for a work platform for an HDX-589...Thanks.. Rich N7TR ex KI3V, N3AMK, WB3JOV www.n7tr.com <http://www.n7tr.com> Telnet: dxc.n7tr.com N7TR DXCluster _________________________________________
For more than 60 years the NCDXC and SCDXC have tirelessly sponsored one of the most popular conventions for DXers and Contesters, the International DX Convention held in Visalia, CA. I have been a r
Click on the link to read the 400+ responses and draw your own conclusions. K6MM and K6TD are the 2011 Chairmen and are looking forward to hearing the "voice of the customer." http://www.surveymonkey
Try this link..... http://tiny.cc/OWSQ2 --Original Message-- From: towertalk-bounces@contesting.com [mailto:towertalk-bounces@contesting.com] On Behalf Of Rich Hallman - N7TR Sent: Sunday, February 2
Chet...There was another updated email sent with this link in it. Tnx http://tiny.cc/OWSQ2 Took me to a website and wants me to sign up for to do a survey, nothing there about results Chet N4FX --Ori
Agree....used Rhino-Flex 600 ft here for many years and works great! A bit spendy..but will last you half a lifetime if taken care of... Rich N7TR Another idea is Rhino Flex - http://shop.hilineco.co
I installed one of my 6 M5X's after being on the ground for a year or so and am seeing High SWR now. Anyone try or have an idea how to test the center balun that has the phasing line that attaches to
I found the issue. The center pin solder joint was bad inside the T=Match hub. Pulled the silicon gunk out and re-soldered....put antenna back on the tower and working fine. Thanks.... Rich --Origina
Or try this...at Array Solutions. 50:75 ohm transformer. Would need one per end. http://www.arraysolutions.com/Products/baluns.htm#50:75 ohm Xfrm 73 Rich N7TR --Original Message-- From: towertalk-bou
Without climbing up the tower to get the answer....What size bolts and length are in the mast clamp of an M2inc OR2800? Thanks... Rich N7TR ex KI3V, N3AMK, WB3JOV www.n7tr.com <http://www.n7tr.com> T
What size diameter are the cross braces on the top section of a HDX572 / 589? Anyone replaced these before? If so...what did you use? I know these need to be welded..... Thanks... Rich N7TR ex KI3V,
MGS is an authorized distributor of new Gigavac relays as well.....Plus a great assortment of used Jennings. I've used many of their Jennings relays with no issues while upgrading the TenTec Titan 42
I have 8 runs of LDF4-50 directly buried. Some 250-300 ft long. No problems over the past 5 years they have been in the ground. I also have 4 inch PVC next to them for the other control cables and co
Last page of the below link shows the cross-reference of the TWB-4001 to RF400... http://www.luxus.cz/dokumenty/new50ohm.pdf --Original Message-- From: towertalk-bounces@contesting.com [mailto:towert
Ive had great luck with these guys.....I have 4 in the air for the past few years with no issues to date. http://www.thebigbearingstore.com/fourboltflangebearing.html 73 Rich N7TR I need a thrust bea
My fence guy was using an auger to drill fence posts and was going to hand dig where we thought my hardline was buried to the tower. I was in town when he started and he "forgot" what we discussed an
Thanks for all the ideas.... Im going with Male N connectors on the ends that go to the tower and the shack....Female N connectors on the splice jumper. Also lots of tape wrap since its going back un
Looking for a M2 Orion 2800 DC Model. Just need the rotor....not control. Let me know if you have one to sell. Thanks... Rich Rich N7TR ex KI3V, N3AMK, WB3JOV www.n7tr.com <http://www.n7tr.com> Telne