Commscope F660BEF 73, Roger The labels on my partial rolls are unreadable now, but I am certain the jacket is PE. Mine is not quad shield, just a single aluminum braid shield plus foil. It is nasty s
I've just made the jump to Win 7 and my favorite old Smith chart program won't run. I have been trying to download SimSmith by AE6TY but his site seems to be down. Can someone send me a copy? Thanks,
I recently discovered a problem with my MFJ-998 tuner that might also be a problem with other tuners. There are two banks of series/parallel capacitors that are switched on the input side of the L ne
I found a realtor who was a ham and knew exactly what I was looking for! 73, Roger I must be lucky, the last three houses I bought (2 in MA, 1 in AZ), could not have been better. The Realtors were qu
A German friend is looking for an Amphenol MS3101A28-21S connector and cable clamp. It's 37 pin female for the AN/SRA-4 antenna coupler. Anyone have one or know where I might find one? 73, Roger N1RJ
Did anyone get a medium that's too large? Swap for a small? 73, Roger _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@
Did anyone get a medium that's too large? Swap for a small? 73, Roger _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@
When sending long addresses that get broken up, put < at the beginning and > at the end. 73, Roger 73/Jon Jon P. Zaimes, AA1K Tower climber for hire http://www.aa1k.us/ Cell: 302-632-2353 Reviews of
Also called stuffing tubes in the marine world. 73, Roger On 6/5/2018 5:13 PM, Bob Matthews wrote: J-Cord connectors are AKA Strain Relief Connectors. They are used for bringing rubber insulated mult
1.924951 1.576014 73, Roger If there are 200 watts out and 10 watts reflected, what's the swr? Tnx. Cheers, Steve K7LXC _______________________________________________ _______________________________
I don't understand what all this discussion is about! Just put your vertical in the center of a 250ft diameter disk of solid silver. Problem solved. 73, Roger ________________________________________
I just wish the DXE radial plate had the holes tapped for 1/4-20. It's a pain getting to the underside with a wrench to remove the nut when you have a bunch of radials attached. 73, Roger ___________
Cushcraft popped into my mind, Robin. I seem to recall they made them quite a few years ago. 73, Roger On 11/17/2018 5:35 PM, K4IDC@comcast.net wrote: Hello to the group. I have one each VHF & UHF ve
Back in my Coast Guard days, we used a system developed by the Navy to seal connectors exposed to the weather. 1. The connection was securely wrapped with self-vulcanizing tape. I don't remember the
I see no mention of UV resistance anywhere in their specs. It is self amalgamating at room temp but what happens when you're hanging off a tower at 30 deg repairing a connector? Not saying you're wro
test _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://lists.contesting.com/mailman/listinfo/tower
It has also paved the way for the county to enact restrictive ordinances! 73, Roger On 6/28/2019 8:04 AM, Dick's wrote: Just a comment about Up The Tower by Steve- I am so glad I bought that book bef
DX Engineering has them 73, AI6LY _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://lists.contesti
If you're doing the GM3SEK mods you DO NOT want 2 inch clamps! The clamp goes around the 5/8 in element. There is a U-bolt that secures the clamp to the boom. 73, Roger Except 10 pairs of 2" for $38
I went up the 625 ft tower on Kure Island in the 60s to relamp it. I just grabbed a safety belt and a bag of bulbs, scampered up and got the job done! Nice photos from the top. 73, Roger Glanced thro