Check with _http://www.bird-x.com/_ (http://www.bird-x.com/) All kinds of devices to control birds Skip, KJ6Y _Communications Service Co_ (http://members.aol.com/kj6y/skip.html) 818-887-3569 ________
Check out Earle M Lorgensen _http://www.emjmetals.com/_ (http://www.emjmetals.com/) I've used them in the past and they have locations all over. Skip, KJ6Y _Communications Service Co_ (http://members
Gary, To fit a tailtwister inside of an LM-470, you need to add a spacer underneath the rotor plate to raise it up about 1 1/2 inches. A piece of angle iron is what the factory used to supply. It had
You raise the plate, not the rotor. I should probably climb my tower and take a digital picture and post it. Maybe in my spare time. The M2 2800 will fit very nicely into the LM-470. You might have t
I took some picture of the rotor plate for the LM-470 with the spacers to allow a Tailtwister T2X rotor to fit and rotate. Go to my web site and click on the LM-470 rotor plate link. Hope this helps.
Klein make a pouch, part number 5142-P. I use 2, one on each side. One for tools snf the other for parts, nuts, bolts, etc. Skip, KJ6Y _Communications Service Co_ (http://members.aol.com/kj6y/skip.ht
Dick, Go online to Hygain's web site _http://www.hy-gain.com/_ (http://www.hy-gain.com/) You can download the manual and get the correct dimensions. Skip, KJ6Y _Communications Service Co_ (http://mem
Several years ago I replaced a US Tower 55 ft that had blown over in exceedingly high winds. The customer decided as long as the insurance is paying for most of it why not go to a HDX-572MDPL, a 72 f
I have a 3 element 80 and a 3 element 40 meter beams for sale. Check at _http://members.aol.com/kj6y/8040antennas.html_ (http://members.aol.com/kj6y/8040antennas.html) Thanks, Skip, KJ6Y _Communicati
Wrong. Lou Tristao worked for Tri-Ex way back (50-60's?) in Tulare, CA. They parted ways and Tri-Ex moved to Visalia and Tristao started his own tower company. He sold out to Palmer Industries in the
Gene, Tri-Ex T-436. 36 ft crank up guyed tower. nested height, 10'9". Weighs 144 lbs. Top section to fit 2" mast. CDR rotor mounts on the top. Maximum dead load capacity, 75 lbs. Maximum antenna load
I've recabled 100s of tower over the past 28 years, Tri-Ex, Tristao, US Tower and even a Rohn crankup. Although not difficult, it is time consuming and does require a little mechanical ability. I usu
Tom, Tri-Ex T-588, Crank up guyed tower. 5 sections, 88 ft. Rotor mounts on top. Safety stops required to relieve tension on cable. Hinged base plate. Maxium dead load capacity, 75 lbs. Maxium wind l
W-51 rated at 9 sq ft at 50 MPH Skip, _KJ6Y_ (http://members.aol.com/kj6y/skip.html) Communications Service Co 818-887-3569 _______________________________________________ ___________________________
LM-354 uses 1/4 in cable. Stainless is OK. Skip, KJ6Y _Communications Service Co_ (http://members.aol.com/kj6y/skip.html) 818-887-3569 _______________________________________________ ________________
The LM-470 uses a 4:1 pulley system on the main lifting cable. Has two lifting cables on the next two sections. Stainless is apprximately 10% less in strength but still within the specs. You can actu
When I replaced a TX-455 for a client that had gone over in the wind, with a HDX 572, I sent a copy of the tower engineering specs to Hilti Products. They came back with the specifications required.