James E. Chaggaris President PowerOne Corporation 1211 W. 22nd St. Suite 802 Oak Brook, IL 60523 Phn: 630-586-9101 Fax: 630-586-9104 web: www.pwrone.com ______________________________________________
It's called the dumbing down of Amateur Radio. That's the end truth.. 73's Jim KJ9A James E. Chaggaris President PowerOne Corporation 1211 W. 22nd St. Suite 802 Oak Brook, IL 60523 Phn: 630-586-9101
I would put up the 70' tower...Tell the inspector if he wants to verify the height to get a tape measure and...START CLIMBING!" 73's Jim KJ9A The township rules permit an antenna/tower/mast up to a m
Ah yes...But most inspectors aren't the brightest bulb in the chandelier....I know, I'm dealing with these goofs right now. 73's Jim KJ9A Jim et al: If I were the inspector, I'd count tower sections.
I feel the same way for this topic and the barrel connector topic....enuf 73's Jim KJ9A James E. Chaggaris President PowerOne Corporation 1211 W. 22nd St. Suite 802 Oak Brook, IL 60523 Phn: 630-586-9
I don't know....I'm sick of the filibustering...Leave that to the politicians and my wife... 73's Jim KJ9A Hold on here: Just what does this thread have to do with Towers and the installation of amat
I don't know why everyone is so up in arms...It's an easy solution...I for one will do my best to "aim" at the worst... 73's Jim KJ9A James E. Chaggaris President PowerOne Corporation 1211 W. 22nd St
Jim: Hope you get the permit from the city....Try getting one in Kane County...1 yr 6mo's and counting.... 73's Jim James Chaggaris President PowerOne Corp. 1020 Cedar Ave. Suite 110 St. Charles, IL
I know I have my ground system layed-out and connected correctly.....If I could just get the damn owl to point due north... 73's Jim KJ9A James E. Chaggaris President PowerOne Corp. 1020 Cedar Ave. S
It tis Rohn 20...I used to have some up until about 20 years ago. 73's Jim N9WW James E. Chaggaris President PowerOne Corp. 1020 Cedar Ave. Suite 110 St. Charles, IL 60174 Phn:(630) 443-6500 Fax:(630
I had two sections of this stuff and 4 sections of Rohn 25G. It fit together perfectly and stayed-up for 5 years until I took it down. It held my tribander without a problem. 73's Jim N9WW James E. C
Ahh! My forgettery is not as bad as you or I thought. As I recall, This mystery tower I bought (the CanadianSpauldingRohn) that fit the 4 sections of Rohn 25 was purposely bowed/modified to fit by so
That giant "sucking" sound you hear with the rise in oil, steel, copper, and other raw materials is coming from both China and India as they go through their own industrial revolutions. Prices will k
Old news...next topic?.... Best Regards, Jim N9WW James Chaggaris President PowerOne Corp. 1020 Cedar Avenue Suite 110 St. Charles, IL 60174 Phn: 630-443-6500 Fax: 630-443-6505 Cell: 630-669-2241 htt
Alan: That's how they are suppose to be configured. But I too had problems using the Polyphaser clamps with my 5/8" ground rods. I had to add about 4 or 5 copper strip shims to get a good firm connec
Well...Before I buy, I would like to see published gain figures and an EZNEC model of this directional owl array... 73's Jim N9WW James Chaggaris President PowerOne Corp. 1020 Cedar Avenue Suite 110
Maybe down the road the NCJ will have an article on phasing this latest creation by Isotron... Best Regards, Jim N9WW James E. Chaggaris President PowerOne Corp. 1020 Cedar Ave. Suite 110 St. Charles
Ditto Jim's comments. I've owned this ladder for three years and it works well and is quite versatile. However, it is a bit heavy and hard to maneuver should you want it fully extended. 73's Jim N9WW
Don't forget LadderTalk.... :-) 73's Jim N9WW (ex KJ9A) James Chaggaris President PowerOne Corp. 1020 Cedar Avenue Suite 110 St. Charles, IL 60174 Phn: 630-443-6500 Fax: 630-443-6505 Cell: 630-669-22
Larry: I'm sorry to hear that your break-in. Unfortunately, that's what's happening and it's not going to get any better. Today, finished copper closed above +/- $4.16/lb. They'll steal anything that