1. Pros and cons on the rope element dampeners? 2. Is it worthwhile to replace those wire pigtails with same-length small-diameter aluminum refrigeration tubes? 3. Set lengths for PHONE/DX Setting/MA
Tks to all who replied. Consensus is, 1. Do what the factory recommends. 2. When all else fails, see 1. ;o) Tks & 73, Dave, N3HE -- Original Message -- From: "David J Windisch" <davidjw@cinci.rr.com>
Small bottle rocket pops scare 'em away for a while. 73, Dave N3HE _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@con
$15 to your conus door. 73 Dave N3HE _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://lists.conte
Fwiw, I replaced the stock booms and boom-to-mast couplers and omitted the stays, on a new TH11, and a used CC 402-CD which I rebuilt, with single 24' *tubes* and pieces of 4"X6" angle, of 6061-T6 al
Fwiw, it takes a face-width of around 24 inches to fit completely inside a section. I have one in an 18 inch faced tower, its motor hangs out one side, and does a fine job of turning a TH11/402CD sta
FS: HyGain TH7, book, good shape, disassembled, $350 ono, *pick up* near Cincinnati. 73, Dave, N3HE in the Cincy white pages _______________________________________________ __________________________
Hi, all concerned: I have a CC A50-6S (20' boom), and enough CC 40M loaded elements to make a 2el 30M yagi. 1. Where do I start to model the two interlaced on the same boom, in EZNEC3? 2. If the inte
Search "positive lightning strike" for some awe-inspiring pictures of lightning-damaged concrete. 73 Dave N3HE _______________________________________________ ________________________________________
No file here, but I have a TH7 & manual, complete, mostly disassembled, on the ground, *for pickup in Cincinnati*, $300. 73 Dave, N3HE _______________________________________________ ________________
Listen to N0FW on 160: 1/4wave vert/3qw elevrad, and 80: fullsize 4sq/3qwelevradper vert. 73 Dave N3HE SNIP _______________________________________________ ___________________________________________
Does "code" still allow clamping? 73 Dave N3HE _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://l
Been getting used to Vista Ultimate for a fortnight now, after years of good XP. A fairly easy experience. I experienced difficulty with getting an old program to load and execute. Found the executab
Makes it a lousy receiving antenna on 30M and up. 73 Dave N3HE SNIP _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@co
I have almost 2 miles of radials and a circle of 8' rods around my tower, all connected at the tower base. The soil even at 3-4' down is powdery-dry. Any thoughts? TIA & 73, Dave, N3HE Cincinnati ___
Right answer. Starting next weekend; BYOB, please ;o) 73 Dave N3HE SNIP _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTal
No wonder K7whatsisname left. Batwings on spare parts for my '1000dee's? Maybe no spare parts for anything? Maybe more spare parts for everything? 73 Dave N3HE Long live meshack the motrac SNIP _____
try: "SAL-MET" (stands for "solder all metals"), made by the Henry Mfg. Co. 117 S. Crawford Street, Danville, Illinois 61832; Tek: (217) 442-3846. 73 Dave N3HE SNIP __________________________________
R&L Electronics randl.com has connector sets for '1000's at around $12, including that "odd" shaped one. 73 Dave N3HE SNIP _______________________________________________ ____________________________