Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+non\s+qsk\s+amp\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+non\s+qsk\s+amp\s*$/: 7 ]

Total 7 documents matching your query.

1. [TenTec] non qsk amp (score: 1): Author: k8bbm@srt.com; Date: Fri, 24 Dec 2010 20:19:54 -0600 (CST); hi, using 544, corsair II - want to key an old amp - NCL2000 - but the delay adjustment for CW in the rigs has narrow range - I would like to slow the relay down a bit more..... suggestions to change; /archives//html/TenTec/2010-12/msg00513.html (7,225 bytes)
2. Re: [TenTec] non qsk amp (score: 1): Author: James Duffer <dufferjames@hotmail.com>; Date: Fri, 24 Dec 2010 20:38:32 -0600; My 544 was the digital version of the Triton IV. Are you sure it is a 544? de wd4air _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.; /archives//html/TenTec/2010-12/msg00514.html (7,904 bytes)
3. Re: [TenTec] non qsk amp (score: 1): Author: "Dr. Gerald N. Johnson" <geraldj@weather.net>; Date: Fri, 24 Dec 2010 20:42:46 -0600; More series resistance or shunt C or both in the delay circuit. Don't have either brought up right now. But the series R should be what you adjust now. 73, Jerry, K0CQ _______________________________; /archives//html/TenTec/2010-12/msg00515.html (7,297 bytes)
4. Re: [TenTec] non qsk amp (score: 1): Author: "Dr. Gerald N. Johnson" <geraldj@weather.net>; Date: Fri, 24 Dec 2010 21:06:59 -0600; On the Corsair II control board, it looks like increase C6 or R12 preferably R35 better than R12. C6 is 33 mfd, R35 is a 10K pot. Don't have anything on hand for the 544, but its probably similar. 73; /archives//html/TenTec/2010-12/msg00516.html (7,473 bytes)
5. Re: [TenTec] non qsk amp (score: 1): Author: "Phil Chambley Sr." <k4dpk@comcast.net>; Date: Sat, 25 Dec 2010 09:40:34 -0500; On the 544, I'd change R-11 from 680 ohms to 4700 ohms, or C-3 from 33 to 47 ufd. Not both. As Jerry said, on R-35, you can cut the ground foil run and bridge the gap with a 4700 ohm. These resistors; /archives//html/TenTec/2010-12/msg00517.html (9,157 bytes)
6. Re: [TenTec] non qsk amp (score: 1): Author: "Phil Chambley Sr." <k4dpk@comcast.net>; Date: Sat, 25 Dec 2010 09:47:56 -0500; R-35 is, of course, on the Corsair II. Phil C. Sr. k4dpk _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec; /archives//html/TenTec/2010-12/msg00518.html (9,710 bytes)
7. [TenTec] non qsk amp (score: 1): Author: k8bbm@srt.com; Date: Sat, 25 Dec 2010 10:53:34 -0600 (CST); thanks, guys, for your assistance. merry Christmas all dave nd0cw _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinf; /archives//html/TenTec/2010-12/msg00520.html (7,083 bytes)

Current List: 1 - 7
Page: [1]