- 1. [TenTec] Omni 6+ mute? (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Thu, 24 Nov 2011 01:27:26 +0000
- Does anyone know a way to mute the Omni 6+ when in cw receive with an external control line? I just want to use Omni 6+ in receive mode, as an auxiliary receiver tuned to the same frequency as the tr
- /archives//html/TenTec/2011-11/msg00343.html (6,838 bytes)
- 2. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Carl Moreschi <n4py2@earthlink.net>
- Date: Wed, 23 Nov 2011 22:45:07 -0500
- Set the power output to zero and use the cw key line connected to the other radio's amp key line. Carl Moreschi N4PY 121 Little Bell Dr. Hays, NC 28635 www.n4py.com __________________________________
- /archives//html/TenTec/2011-11/msg00344.html (7,563 bytes)
- 3. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Richards <jruing@ameritech.net>
- Date: Thu, 24 Nov 2011 01:52:12 -0500
- I am a rookie at this, but this is my best shot, I have just started researching these sorts of devices for an application in my shack...so it seemed coincidentally timely enough. A) Maybe the DX Eng
- /archives//html/TenTec/2011-11/msg00345.html (9,422 bytes)
- 4. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Thu, 24 Nov 2011 10:59:57 +0000
- Thanks for the responses. Carl, I tried this and the problem is that even though the power is set to zero, the Omni 6+ is putting out a very low power signal that I'm hearing interfering with the oth
- /archives//html/TenTec/2011-11/msg00346.html (9,863 bytes)
- 5. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
- Date: Thu, 24 Nov 2011 12:11:42 +0100
- Sounds like you need to de-activate the "R" line without activating the "T" line. In the old analog rigs this would have been easy enough to do. In the OM6 it's probably done in the computer now, so
- /archives//html/TenTec/2011-11/msg00347.html (8,872 bytes)
- 6. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: wa3fiy@radioadv.com
- Date: Thu, 24 Nov 2011 08:53:20 -0500
- Greetings all. My Omni VI/O3 has a MUTE jack on the rear panel which will mute the receiver when asserted. According to the manual "Whenever the MUTE line goes to ground, a MUTE RQ signal is...sent t
- /archives//html/TenTec/2011-11/msg00348.html (8,394 bytes)
- 7. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Thu, 24 Nov 2011 12:03:52 -0500
- Thanks but have you actually tried it? My mute jack does NOT mute the receiver when grounded. Thanks for all the responses. Like Rick suggests, I'm going to have to tear into things which isn't going
- /archives//html/TenTec/2011-11/msg00349.html (9,837 bytes)
- 8. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
- Date: Thu, 24 Nov 2011 18:30:09 +0100
- Barry, I was thinking about this some more. I don't have the schematic here (ok, I could download it I guess). Anyway, once you determine "where" the "T" and "R" signals are generated, either on a Co
- /archives//html/TenTec/2011-11/msg00350.html (11,275 bytes)
- 9. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: "WA3FIY" <wa3fiy@radioadv.com>
- Date: Thu, 24 Nov 2011 13:55:54 -0500
- Yes I have tried it...just now, and it does work very well. -Lee _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo
- /archives//html/TenTec/2011-11/msg00351.html (9,752 bytes)
- 10. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Ken Brown <ken.d.brown@hawaiiantel.net>
- Date: Thu, 24 Nov 2011 09:27:20 -1000
- Then your Omni VI is broken. Repairing the Omni VI to make the mute input function properly is probably preferable to building a workaround. The mute input may not work because someone has modified
- /archives//html/TenTec/2011-11/msg00352.html (8,942 bytes)
- 11. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Thu, 24 Nov 2011 17:23:12 -0500
- Thanks for all the responses and the troubleshooting tips. I'm going to try and open up the Omni 6 sometime tomorrow and have a look around and see if there's a quick repair that can be made. 73, Bar
- /archives//html/TenTec/2011-11/msg00355.html (10,120 bytes)
- 12. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Fri, 25 Nov 2011 14:09:05 +0000
- Another Omni 6+ was available to test and the mute seems to work fine in this other Omni 6+, just like many of you said it should. So the mute circuit WAS defective in the original Omni 6+ and apolog
- /archives//html/TenTec/2011-11/msg00362.html (11,089 bytes)
- 13. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Barry N1EU <barry.n1eu@gmail.com>
- Date: Fri, 25 Nov 2011 22:03:22 +0000
- Just to follow up and close this out. The mute in the Omni 6+ isn't a hardware mute, and that's what was throwing me for a loop. The MUTE input simple drives an internal MUTE RQ line and I believe th
- /archives//html/TenTec/2011-11/msg00366.html (11,765 bytes)
- 14. Re: [TenTec] Omni 6+ mute? (score: 1)
- Author: Richards <jruing@ameritech.net>
- Date: Sat, 26 Nov 2011 00:34:08 -0500
- do what I'm trying to do. == Sorry for any wild goose chase, Barry... I am still learning... guess I have a bit more to go ! At least my local electronics Elmer looked over my latest home brew switc
- /archives//html/TenTec/2011-11/msg00368.html (8,774 bytes)
This search system is powered by
Namazu