Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Filter\s+attenuation\s+problem\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Filter\s+attenuation\s+problem\s*$/: 6 ]

Total 6 documents matching your query.

1. [TenTec] Filter attenuation problem (score: 1): Author: "Jack Wigal" <jackay2@verizon.net>; Date: Mon, 18 Dec 2006 12:59:09 -0500; I recently purchased an Omni-6 and later added a #217 500hz filter to the 9 mhz IF. With the amplifier jumped in I'm getting about two S-units of attenuation and with no amp I'm getting about three S; /archives//html/TenTec/2006-12/msg00451.html (7,120 bytes)
2. Re: [TenTec] Filter attenuation problem (score: 1): Author: Ken Brown <ken.d.brown@hawaiiantel.net>; Date: Mon, 18 Dec 2006 20:33:30 -1000; Do you have another filter you can put in that slot. If so, see how much attenuation you get with the other filter. Then decide from the numbers whether the fault seems to be the filter, or the switc; /archives//html/TenTec/2006-12/msg00457.html (8,458 bytes)
3. Re: [TenTec] Filter attenuation problem (score: 1): Author: Ken Brown <ken.d.brown@hawaiiantel.net>; Date: Mon, 18 Dec 2006 21:26:03 -1000; Hi again Jack, Another possibility, I should have mentioned in my first post, is that you may not have the PBT set so that the NAR 9MHz 217 filter bandpass is coincident with the 6.3 MHz bandpass. Sw; /archives//html/TenTec/2006-12/msg00459.html (9,215 bytes)
4. Re: [TenTec] Filter attenuation problem (score: 1): Author: "GARY HUBER" <glhuber@msn.com>; Date: Tue, 19 Dec 2006 11:02:17 -0600; Note: Pg 1-3 Para 1.8-2 INSTALLING 9 MHZ IF FILTERS.... "Models 216, 217, and 219 require the high gain setting." "Position the jumper plug to connect the correct pins on JG1 and JG2 as shown in Figu; /archives//html/TenTec/2006-12/msg00466.html (8,787 bytes)
5. [TenTec] Filter attenuation problem (score: 1): Author: <k8vf_mark@centurytel.net>; Date: Tue, 19 Dec 2006 12:34:23 -0500; I have the same issue and it IS the filter in my case. 217 filter. Replacement filter solves issue. Does anyone know the capacitor values on the board as mine are not marked? Thank you for any advice; /archives//html/TenTec/2006-12/msg00467.html (7,500 bytes)
6. [TenTec] Filter attenuation problem (score: 1): Author: "Jack Wigal" <jackay2@verizon.net>; Date: Tue, 19 Dec 2006 13:23:49 -0500; Folks, I failed to tell you in my first post that my rig is the Omni 6 with option 3, so I have two optional filter slots in the 9mhz IF. I tried a 1.8 filter in the same slot and it loses about 1/2; /archives//html/TenTec/2006-12/msg00487.html (7,783 bytes)

Current List: 1 - 6
Page: [1]