Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Corsair\s+II\,\s+PTO\s+output\s+level\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Corsair\s+II\,\s+PTO\s+output\s+level\s*$/: 7 ]

Total 7 documents matching your query.

1. [TenTec] Corsair II, PTO output level (score: 1): Author: Thomas Kuehl <qrp_op@yahoo.com>; Date: Mon, 24 Mar 2014 13:06:09 -0700 (PDT); Hi, Does anyone know what the correct peak-to-peak output level is for a properly working Corsair II PTO? Any assistance is appreciated. '73, Thomas - ac7a _____________________________________; /archives//html/TenTec/2014-03/msg00207.html (7,453 bytes)
2. Re: [TenTec] Corsair II, PTO output level (score: 1): Author: Steve Hunt <steve@karinya.net>; Date: Mon, 24 Mar 2014 20:34:22 +0000; All four of mine measure close to 1.2v p/p Steve G3TXQ On 24/03/2014 20:06, Thomas Kuehl wrote: Hi, Does anyone know what the correct peak-to-peak output level is for a properly working Corsair II PT; /archives//html/TenTec/2014-03/msg00208.html (7,457 bytes)
3. Re: [TenTec] Corsair II, PTO output level (score: 1): Author: "Jerry Haigwood" <jerry@w5jh.net>; Date: Mon, 24 Mar 2014 21:11:13 -0500; Hi Steve, What was the load impedance? Jerry W5JH "building something without experimenting is just solder practice" All four of mine measure close to 1.2v p/p Steve G3TXQ On 24/03/2014 20:06, Thomas; /archives//html/TenTec/2014-03/msg00209.html (8,500 bytes)
4. Re: [TenTec] Corsair II, PTO output level (score: 1): Author: Steve Hunt <steve@karinya.net>; Date: Tue, 25 Mar 2014 08:21:17 +0000; It was measured "in-situ" - so whatever load the following mixing stage represents. Steve G3TXQ _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.; /archives//html/TenTec/2014-03/msg00211.html (7,800 bytes)
5. Re: [TenTec] Corsair II, PTO output level (score: 1): Author: Doug Reid <n1068d@aol.com>; Date: Tue, 25 Mar 2014 10:17:46 -0400 (EDT); If you don't mind my asking, what problem are you experiencing with your rig ? I spent a few hours last week resurrecting a Triton 544 PTO and associated problems with the VFO. Doug WD4LNW It was mea; /archives//html/TenTec/2014-03/msg00212.html (8,803 bytes)
6. Re: [TenTec] Corsair II, PTO output level (score: 1): Author: Thomas Kuehl <qrp_op@yahoo.com>; Date: Tue, 25 Mar 2014 07:42:08 -0700 (PDT); Hi Steve, Thank you very much for the information regarding the output levels from your Corsair PTO. '73, Thomas - ac7a All four of mine measure close to 1.2v p/p Steve G3TXQ ___________________; /archives//html/TenTec/2014-03/msg00213.html (9,267 bytes)
7. Re: [TenTec] Corsair II, PTO output level (score: 1): Author: Thomas Kuehl <qrp_op@yahoo.com>; Date: Tue, 25 Mar 2014 07:51:37 -0700 (PDT); Hi Jerry, The Corsair II fold-out shows the PTO output routed to the 80975 Oscillator-Mixer board. The signal splits at that point going to U1, the TL442 mixer IC, for all bands except 20 meters, a; /archives//html/TenTec/2014-03/msg00214.html (10,605 bytes)

Current List: 1 - 7
Page: [1]