Hi Group! Having gotten Carl's program and being Mightly Pleased with it have found that his program will also work with the 1208 and 1210 xcvs. If you have either/or of these and are unhappy give me
Hi Peg, DeOxit works great,you can get it most any good electronics supply house(sorry ratshack does not stock it). 73 de Bill _______________________________________________ TenTec mailing list TenT
Hi Ron, I knew Ed Clegg (then W2LOY,later W8LOY) when he had his business in East he'd object to Ten Tec using some of the Greco-Roman names that he used to name his rigs with:"Venus"-a good 6mtr ssb
Hi Gary, Have a Jupr myself and ran into the same problem abt 3 mos ago-Check the resistance of the windings of the BP filter relays,both windings are in parell and shoud read abt 120 ohms per band-i
Hi Gary , Messed up on the resistance readings across the solenoid coils: both coils are in paralel on any given band so when you read across them ,the DC resistance should be 205 ohms.Any other read
Hi Mike, What do you want for that 1208 Xcvr? Doesn't have to work ,just be complete. 73 de Bill W4NJF I goofed on my original posting. The Corsair that I am taking to Sevierville in NOT a Corsair II
Hi Gary,Glad to be of some help.Just remember,don't use a lot of heat on these little relays when resoldering them in. This may be part of the problem;I suppose in a jam(like during a contest),you co
HiBill, I sent you a check last year to that Alphretta,Ga QTH to keep this website going but the Post Office returned it as being UNDELIVERABLE.Is this a good snailing QTH or what? 73 de W4NJF To all
Hi Pete, Seem to reall the old Heathkit LMO for the SB series tuned 5.0 to 5.5 Mhz;Heath had a separate LMO,(SB640?) that enabled the SB 100/101 to operate split. 73 de Bill W4NJF Looking for a worki
Hi Tom, Haven't tried any of Bob's mikes on my Jupiter yet,so I can't comment on them.However your comments on mike impedance are right on the money.I have a modified D-104 that worked real good with
Hi Tim, have a Scott TV in my living roon that radiates RF Hash that you would not believe.It is model HTS 200-has a great picture,but a truly lousy front end RF wise.Got to turn this puppy off even
Hi Winston, Thourhly enjoyed your comments.Thomas Wolfe not withstanding,you can go home again.Have recently acquired my first "real" ham rcvr that I got while a Novice in 1961-an RCA ACR-155(albeit
Hi Grant, Have got to disagree with on this subject.Another poster noted that the DC resistance from the shell of the mike jack was abt 6 OHMS and asked to anyone else to try it-the DC reisistance on
They were probably afraid to design a HT rig because its hard to tell the user that the "rubber ducky"antenna is too close to the rcvr and maybe you had best relocate it down the street if you wan't
Good point Bob;did the readout go totally bananas when you keyed it(or did they say you had RF in the shack or the antenna was too close to the rig!) -- Original Message -- From: "Rob Atkinson, K5UJ"
Hi Mike, Other than the front panel readout,the Peg is basically the same as the Jupe(the Jupe,s original name was "Pegasus FP")so the troubleshooting hint I gave to Rick should apply to the Peg also
Hi Mike, had a Scout tha that had the same problem.its a seating glitch where the module does not "home" allthe way into the socket in the Scout mainframe..Try this:be sure that the female mating plu
Dear Dr Jurassic, I,having a postdoctoral degree in Lunar Botany,have NEVER found it necessary to post my academic credrentials on this reflector site. _______________________________________________
To all the gang at Dollyland(and especially to Paul Clinton),I'd like to extend sincere thanks for resolving a parts problem . I bought a 1208 transveter kit from a fellow ham off this reflector site
Hi Mark, I use a D104 with my Jupiter,but had to do the following mods to it to get it to fly(the D104 worked gud with my old Scout,not so hot with the Jupe). 1. If ur D104 is the unamplified type,bu