Hi John Are you sure that COM 3 is actually the one connected to your O2 ? Does your old XP laptop have a serial port ? If so I would be using a serial cable direct from the laptop to the O2. Have yo
OK John It's years since I had anything with XP on it so I can't remember how things work. However, if it's similar to current versions ie W10, you can check your computer com ports by right clicking
Hi Gary I would like one of the main tuning knobs for the Omni VI please. Please let me know how much including postage to Sydney, Australia. My address is correct on my QRZ page. 73 Barry Simpson VK
Hi Gary Please give me a PayPal address and I will pay you the US$30. 73 Barry VK2BJ _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.
I have recently acquired an Omni VI Option 3 which is working but needs some TLC to bring it up to par both physically and electronically. One thing I need to do is to correct the frequency calibrati
Hi Allan To enable me to make some suggestions, please can you provide some more information on your set up please: Computer O/S - W10 ? Type of serial to USB convertor ? - I assume that you are usin
K4FW Barry VK2BJ _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I am looking for a replacement Low Level Driver/NB Board for my Omni Vl Option 3. My noise blanker does not work at all but otherwise the rig is now fine. The board number per the manual is 81608. An
Hi Petr Do you really want 3.033xd or 3.033xe ? I have both and use 3.033xe. I also have 3.029 which is very good. How is the O2 ? Barry VK2BJ On Tue, 13 Aug 2019 at 18:55, Petr Ourednik <indians@xsm
My Omni VI Option 3 has developed a problem on SSB transmit whereby there is a permanent tone/carrier of about 1.2kHz above the actual frequency and within the audio passband. It was first brought to
I posted the message below some weeks ago. Not having had a response, I am repeating it again below with a few additional comments. My Omni VI Option 3 has a problem on SSB transmit whereby there is
Good morning John, Bob and Gary Thank you very much for all your suggestions in relation to the problems I am experiencing with my Omni Vl. I did buy it to upgrade and play with but I had not expecte
After a two year search, I have finally acquired a very nice Omni Vl Plus. I would like to know if anyone has designed/undertaken a modification to eliminate the slow noisy amplifier relay to allow s
I am just getting to grips with a new Omni VI Plus that I have very recently acquired. It is in almost as new condition and generally works very well. I decided to listen to the Omni's keying on my T
I have just read all the information on the Ten Tec Wiki which answers all my questions and more and confirms that my assumptions are correct. It also solves a previous post I made by way of a simple
Hi Dennis It is undoubtedly the battery that needs replacing. I had a friend's 566 to sort out and that did exactly the same but was fixed when I replaced the battery. Go to the Ten Tec Wiki, then to
Within the last few days, my O2 has had audio issues when first switched on. What happens is that a low level of continuous clicking occurs either from the headphones or loudspeaker, whichever is con
Thanks Petr I will let you know the outcome when I have done the re-caping. 73 Barry VK2BJ _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.conte
I have just finished re-capping the A9 board only to be really disappointed that the rig does not now work at all. When I switch on power, there is the usual relay clicking but the S Meter doesn't li
Further to my email below, the panic is over. After very careful examination of the A9 board for the umpteenth time with my illuminated magnifying glass, I discovered that one of the five 22 ohm resi