*Below is what we found. I have 2 on the way to try out before purchasing about 25 of them. * * 73 from Wade/KJ4WS* (KO) 1017-18-1 *Wabash* RF reed relay used throughout the KWM-380. High quality. Ea
*Is there no salvaging the original switch? Just curious here, how did it fail?* * 73 from Wade/KJ4WS* -- *Living one day at a time with Jesus as my Savior. But, still having Fun.*
*You know your getting old, when you can remember the pin out on a 6GH8 or 12BY7 tube but, not why you came into the Shack just now. And you're really getting old when. Your best Friend asks " Are yo
*Where I come from, the phrase " present this Award " gets used a lot. A Diploma should be something you have studied for. And a Certificate would notate that something has been Certified. I believe
*OK. I am done studying. The ARRL in the link below calls them Awards, which are given out by the Awards Committee ...... I will now turn my feeble mind back to Idle and try to save the last few hair
*I also need Ten Tec Parts. We need an end cap that slides into the side of the case, between the front panel and the radio. One from a Paragon, Omni 5 or 6 should fit. Also, I maintain the BBC Club
*I believe that most of this problem, stems from the fact that the eye sees Red as much brighter. We know for a fact that the eye has more trouble at focusing when the color red is involved. This is
*This may not be the correct way to do it but, we used one of the small insulin syringes that my Miss Brenda, uses for her injections. * * 73 from Wade/KJ4WS* -- *Living one day at a time with Jesus
*Well my guess is that I am about to get really Slammed. We have used several OCF Antennas. At 100 Watts, things are pretty good. My problems appear anytime we try to go QRO. At a Kilowatt there does
*Hello Rick,* * You have a very good memory! I use the Ugly Balun ( about 12 feet of RG-8 wrapped around a 3 inch PVC Pipe ) this is a Current Balun. Although we don't like the loss from the Coax. We
*Once again I walk forward with my Asbestos Suit on hi .. hi .. In the QST Article linked below, modeled on a 66 foot dipole. The SWR and Loss Figures comparing Ladder Line ( Windowed Line ) and Coax
*Randy,* * Check out your inbox for the message from tvman1954@gmail.com <tvman1954@gmail.com> The 2 page schematic is all that I have. Sure wish that we could have been more helpful.... Just remembe
*Hello Gary,* * Wade here KJ4WS. Here is what I found after looking at the service manual. The 40 Meter Crystal is Y4. Sorry but I didn't go deep enough to get the frequency. You could have a bad cry
*Sorry guys, The long winded message should have been sent directly to Gary. * * 73 from Wade/KJ4WS* -- *Living one day at a time with Jesus as my Savior. But, still having Fun.*
*Thanks Barry,* * You made that poorly worded advise look really good. We can only hope that it helps others. * * 73 from Wade/KJ4WS* -- *Living one day at a time with Jesus as my Savior. But, still
*Try Bob/K4TAX, he was one of the Beta Testers for Ten Tec on the Eagle and several other models. * rmcgraw@blomand.net *..... Bob, is a really great guy and any rig he sells will be in 110% working
*The manual you need, should be in an email from me. It is in .pdf format. Seems like I am moving lots of Bytes around here lately.* * 73 from Wade/KJ4WS*
*That was a good bit of advise on the Low Pass Filter Board Joe. Mine was the small Pin Diodes that drive the relays. Mine had a really high SWR and pulled WAY TOO MANY AMPS on transmit. If the rig i
*Your post came through just fine but, I believe that you were about 20 Hz low on frequency and had just a tiny bit of RF on your signal.... It may just be my eyes or this monitor?? >> 73 from Wade/K