A few months ago, I borrowed an Orion and added support for it to the N1MM Logger (see sig). I have now received my own Orion and am doing some planning of what Orion-specific features I should add t
Here is a real-world example. The Orion does not have a relay that mutes the mic when a sound card dvk message is sent via the aux input. However, I was able to set the mic level to 0 prior to sendin
A simple solution would be to have a quick press of the A>B button just transfer the frequency. A two second press could be used to transfer mode, bandwidth, agc, etc. This short/long press is used w
This question has come up several times. As I understand it, the file interface only supports the following interface. · LINE 1 = Main VFO Frequency in Mhz, with a single decimal point. &middo
The Koss QZ Pro model *is* noise cancelling. Works pretty well. About $60. 73, Tom Wagner - N1MM Check out the N1MM Free Contest Logger at: http://www.n1mm.com http://groups.yahoo.com/group/N1MMLogge
http://www.circuitcity.com/ccd/Search.do?c=1&context=&keyword=qz+pro&searchS ection=All $60.00 sounds good to me. R these just head phones... I am looking for a good headset... And where could I get
I have been battling with what I thought was RFI for quite a while now. I won't go into all the details. My setup is an Orion, Ameritron AL1500 & Heil Proset w/ the HC4 element. I stupidly set the mi
More to report. The symptom is easier to recreate with the mic gain set at 100, however it happens with mic gains down to 20, and that is below what the HC-4 element needs to drive the radio. I have
Thanks to those that responded. I think I have some residual RFI problems, but that was not the cause of the problem listed below. The main issue was the shield of the mic in the Heil TT dongle was i
Page 9 of the Orion manual shows ground as pin 2. Page 10 of the manual shows minus (-) as pin 2. It also shows white as pin 2. A web search shows the mic pinout for the Omni VI as Pin 2 is ground. h
Since this didn't get answered, I'll ask again. Is it TenTec that is not following the IEC/AES standard? Bottom line, if I have a mic with simple coax -- one center conductor plus shield -- to which
I tried connecting the shield to the mic connector and the RFI-like noise was worse than ever. My Orion shows 1/2 ohm resistance between the mic connector and the rear ground lug. 73, Tom Hi Tom and
I failed to point out that this is using a stock Heil Proset which has only one wire plus a shield to the mic. I'm sure with a two-wire + shield situation that grounding the shield is the proper appr
I have tried the aux input. It does work much better for whatever reason. Thanks for the help. 73, Tom --Original Message-- From: N0KHQ@aol.com [mailto:N0KHQ@aol.com] Sent: Thursday, December 23, 200
Well I sent the radio back to Tentec, because they said they had a fix for this type of problem. They applied 4 mods, two of which seemed relevant to the problem, and the problem went away. Go figure
These are the stats for the N1MM.com website for the past 2 1/2 years. This represents 81,000 hits. About 72% are 1024 x 768 or better... Screen Share 1024x768 53.14% 800x600 24.70% 1280x1024 12.14%
http://www.k1el.com/ Winkey. See list of supported software... Tom Wagner - N1MM Check out the N1MM Free Contest Logger at: http://www.n1mm.com http://groups.yahoo.com/group/N1MMLogger/ Using the Log
Bob -- What do you mean by RS-232 command speed issue? 73, Tom Wagner - N1MM Check out the N1MM Free Contest Logger at: http://www.n1mm.com http://groups.yahoo.com/group/N1MMLogger/ I have already ma
This happened to me on 20 meters. It was a synthesizer adjustment that was corrected when I sent it to TenTec. Call them, they recognized the symptom immediately. 73, Tom I discovered that my main re
It's not a quirk. It's a feature. The software will mute the mic for you when playing a wav file through the aux port. That way you don't need to buy a rigblaster type box. I own an Orion. I made the