Grant: I just checked mine and it appears to do the same thing. Setting up the Main at LSB, BW=1800, PBT=0, and the same thing on the Sub, there is a very noticeable difference. Tweaking the Sub PBT
I found a large ham radio outfit here in CA who would, (for the right customers, or course!), ship the empty box out state while the customer carried off the goods. No one ever questioned why a 1.5 k
Carl: Does the 200 Hz on the Main RX apply to all bandwidths and modes? Ron N6AHA _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com
Bob: How are you determining the output of the Centurion on SSB? I believe that if you looked at the output on a spectrum analyzer, you would find that the Orion II is driving it to a true PEP value
I just ran a test on my O2 with a spectrum analyzer, and although I didn't have the perfect test conditions, I noted that the CW trace at 100% and 50% power level setting was the same as the SSB peak
Yesterday I cured a terrible noise problem I had here on 75 meters that used to come up in the evening and ran a solid S-9 and had been around for a couple of weeks. I went out in the mobile looking
Great test, Lin! This confirms my more subjective observation that both the HW and SW NB's work extremely will on short-duration peak noise. Probably the stronger and shorter the peak, the better it
Has anyone else noticed that the Ten Tec web site, other than the index page is down? Ron Castro Chief Technical Officer Results Radio, LLC _______________________________________________ TenTec mail
I would believe that there are a lot of things in the O1 v. 2 upgrade that are identical to the O2, probably because substantial parts of the code were simply "cut and past" copied into the .ruf file
Find a free "hex editor" if you don't have one already, and simply open the file with it. You'll see a neatly laid-out, extremely long but totally incomprehensible matrix of hex numbers. It goes on f
That is all valuable information. I want to add that my Orion II had a problem with RF, but it was coming in via the headphone wire and the CW paddles connected to the back. Ferrites solved the probl
It wouldn't put me to sleep...I love that stuff, too! Ron N6AHA _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/
I downloaded and installed the new update for the O2. Can't see any difference so far, but the little dot next to the Step number is gone! Not that it bugged me...I couldn't see it unless I really lo
I'm fairly knowlegeable in that area, since I routinely prepare and file FCC applications for high-power FM broadcast stations, up to 50 kW ERP. The low-duty cycle of typical Amateur SSB and CW opera
This can still cause high RF in the shack if there is much SWR, radiation from a tuner or linear, signal induced on the feedline, radiation from long or resonant ground lines or re-radiation from nea
Remember that the mic setting is only relative since there is a "master level control" pot accessed through a hole on the underside of the rig near the mic connector. Changing that will cause you to
Try that pot underneath. Ron Castro Chief Technical Officer Results Radio, LLC _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/ma
Maybe they need to bring Doug Smith, KF6DX back for a consult. Ron Castro Chief Technical Officer Results Radio, LLC _______________________________________________ TenTec mailing list TenTec@contest
I haven't noticed any of that. I'll check the frequency response on SSB when I get a chance. Ron Castro Chief Technical Officer Results Radio, LLC _______________________________________________ TenT
I found my first bug in the Orion II 2.031 firmware. I noticed that the receive signals were down near zero, as if the antenna was disconnected. It was. In QSK mode (Ten Tec Titan 425 with QSK), at s